What is supposed to happen after "build complete"?
Red Hat Enterprise Linux AS release 4 (Nahant Update 6)
Kernel 2.6.9-67.ELsmp on an i686
Downloaded auto installer. Only wanted to install printing only, so selected 'p'. However, I got no reboot required or any such message after the "build complete" message. What now? I can't run the hp-setup command.
Here is the output of the install session.
$ sh hplip*.run
Creating directory hplip-2.8.12
Verifying archive integrity... All good.
Uncompressing HPLIP 2.8.12 Self Extracting Archive.
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
.......
HP Linux Imaging and Printing System (ver. 2.8.12)
HPLIP Installer ver. 5.0
Copyright (c) 2001-8 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Installer log saved in: hplip-install_
\
note: Defaults for each question are maked with a '*'. Press <enter> to accept t
he default.
INSTALLATION MODE
-----------------
Automatic mode will install the full HPLIP solution with the most common options
.
Custom mode allows you to chose installation options to fit specific requirement
s.
Please choose the installation mode (a=automatic*, c=custom, q=quit) : c
Initializing. Please wait...
warning: Invalid ppd_dir value: None
INSTALL TYPE
------------
For most users, it is recommended to install HPLIP with full support (scanning,
faxing, toolbox, etc).
For servers or minimal installations, you can also install print support only (H
PIJS only).
Install full hplip support (recommended) or print-only support (f=full hplip sup
port*, p=printing only support, q=quit) ?p
INTRODUCTION
------------
This installer will install HPIJS version 2.8.12 on your computer.
Please close any running package management systems now (YaST, Adept, Synaptic,
Up2date, etc).
DISTRO/OS CONFIRMATION
-------
Distro appears to be Red Hat 4.
Is "Red Hat 4" your correct distro/OS and version (y=yes*, n=no, q=quit) ? y
SELECT HPLIP OPTIONS
-------
You can select which HPLIP options to enable. Some options require extra depende
ncies.
Do you wish to enable 'CUPS support for HPIJS' (y=yes*, n=no, q=quit) ? y
ENTER ROOT/SUPERUSER PASSWORD
-------
Please enter the root/superuser password:
Password incorrect. 2 attempt(s) left.
Please enter the root/superuser password:
Password accepted
RUNNING PRE-INSTALL COMMANDS
-------
READY TO BUILD AND INSTALL
-------
Ready to perform build and install. Press <enter> to continue or 'q' to quit:
PRE-BUILD COMMANDS
------------------
BUILD AND INSTALL
-----------------
Running './configure --prefix=/usr --disable-qt4 --enable-
-enable-doc-build --enable-qt3 --enable-gui-build --disable-
--disable-pp-build --enable-
nly-build --enable-scan-build --disable-
Please wait, this may take several minutes...
Command completed successfully.
Running 'make clean'
Please wait, this may take several minutes...
Command completed successfully.
Running 'make'
Please wait, this may take several minutes...
Command completed successfully.
Running 'su -c "make install"'
Please wait, this may take several minutes...
Command completed successfully.
Build complete.
POST-BUILD COMMANDS
-------------------
$ hp-setup
ksh: hp-setup: not found
Question information
- Language:
- English Edit question
- Status:
- Answered
- For:
- HPLIP Edit question
- Assignee:
- No assignee Edit question
- Last query:
- Last reply:
Can you help with this problem?
Provide an answer of your own, or ask keys2heaven for more information if necessary.