Wireless Network controller [0280]: Realtek Semiconductor Co., Ltd. Device [10ec:8171] (rev 10) can successfully detect but cannot connect to wireless network using Compaq 320 in Ubuntu 10.04.1 LTS -> using driver=rtl819xSE driverversion=0014.0115.2010
I have just installed ubuntu on my Compaq 320, and the wireless is not picking up the signal. It works fine when I plug it in though. I am also running my dell which has unbuntu as well, and it is having no problems picking up a signal. Any ideas?
Question information
- Language:
- English Edit question
- Status:
- Solved
- Assignee:
- No assignee Edit question
- Solved by:
- Forrest Brandt
- Solved:
- Last query:
- Last reply:
Revision history for this message
|
#1 |
Can you give the output of:
sudo lshw -C network
Thanks
Revision history for this message
|
#2 |
I ran the command you posted; this is what came up! Is it the info u asked for?
*-network
description: Wireless interface
product: Realtek Semiconductor Co., Ltd.
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:02:00.0
logical name: wlan0
version: 10
serial: 70:f1:a1:d2:24:d2
width: 32 bits
clock: 33MHz
resources: irq:17 ioport:
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:85:00.0
logical name: eth0
version: 02
serial: 1c:c1:de:8d:cc:65
size: 10MB/s
capacity: 100MB/s
width: 64 bits
clock: 33MHz
resources: irq:29 ioport:
Revision history for this message
|
#3 |
Ok and what is the output of:
sudo iwlist scan | head -n 20
Thanks
Revision history for this message
|
#4 |
Hi,
Please first connect your network card to the wireless router using an ethernet cable (also known as a LAN cable).
In order to gather essential troubleshooting information about your wireless card, please follow this procedure:
Step 1: Open Terminal from "Applications-
Step 2: Please copy-paste the following command from the https:/
Tip: If you have a wheel mouse or 3 button mouse you do not need to type commands into the Terminal. Highlight the command written on the page. Move your cursor anywhere in the Terminal and press the wheel or middle button. Automatic Copy and paste! No spelling mistakes! No Typos! No other errors!
sudo apt-get update; sudo apt-get install hwinfo grep; sudo lshw -C network; rfkill list; sudo iwlist scanning; cat /etc/network/
Step 3: Please post results (copy/paste terminal output) on this thread. The troubleshooters here need to see the full Terminal output from running the above command.
Regards,
Mark
Revision history for this message
|
#5 |
sats "interface doesn't suppot scanning"
Revision history for this message
|
#6 |
Is compaq 320 the FULL model name. I cannot find a "Compaq 320"
Revision history for this message
|
#7 |
action,
It was bought in Thailand, and just says Compaq 320, even in the literature that came with the computer it did not give further detail, wierd I know.
On the serial number sticker on the bottom it goes as follows
Model: Delphi
Modal Number: d40
It came pre-installed with SuSe SLED 11 by Novell.
Revision history for this message
|
#8 |
Mark,
here is what is says: I posted the whole thing because I'm not sure which exact part you need.
[sudo] password for forrest:
Hit http://
Ign http://
Ign http://
Ign http://
Ign http://
Hit http://
Ign http://
Ign http://
Ign http://
Ign http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Ign http://
Ign http://
Ign http://
Ign http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Reading package lists... Done
Reading package lists... Done
Building dependency tree
Reading state information... Done
grep is already the newest version.
The following extra packages will be installed:
libhd16
The following NEW packages will be installed:
hwinfo libhd16
0 upgraded, 2 newly installed, 0 to remove and 271 not upgraded.
Need to get 744kB of archives.
After this operation, 2,060kB of additional disk space will be used.
Do you want to continue [Y/n]? y
Get:1 http://
Get:2 http://
Fetched 744kB in 1s (392kB/s)
Selecting previously deselected package libhd16.
(Reading database ... 122714 files and directories currently installed.)
Unpacking libhd16 (from .../libhd16_
Selecting previously deselected package hwinfo.
Unpacking hwinfo (from .../hwinfo_
Processing triggers for man-db ...
Setting up libhd16 (16.0-2) ...
Setting up hwinfo (16.0-2) ...
Processing triggers for libc-bin ...
ldconfig deferred processing now taking place
Hardware Lister (lshw) - B.02.14
usage: lshw [-format] [-options ...]
lshw -version
-version print program version (B.02.14)
format can be
-html output hardware tree as HTML
-xml output hardware tree as XML
-short output hardware paths
-businfo output bus information
options can be
-class CLASS only show a certain class of hardware
-C CLASS same as '-class CLASS'
-c CLASS same as '-class CLASS'
-disable TEST disable a test (like pci, isapnp, cpuid, etc. )
-enable TEST enable a test (like pci, isapnp, cpuid, etc. )
-quiet don't display status
-sanitize sanitize output (remove sensitive information like serial numbers, etc.)
-numeric output numeric IDs (for PCI, USB, etc.)
Revision history for this message
|
#9 |
That is not the full output.
The correct command STARTS with sudo and ENDS with the word restart.
The command you used was not the command I posted here.
Here it is one more time:
sudo apt-get update; sudo apt-get install hwinfo grep; sudo lshw -C network; rfkill list; sudo iwlist scanning; cat /etc/network/
Revision history for this message
|
#10 |
Second try,
forrest@
[sudo] password for forrest:
Hit http://
Ign http://
Ign http://
Ign http://
Ign http://
Hit http://
Ign http://
Ign http://
Ign http://
Ign http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Ign http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Ign http://
Ign http://
Ign http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Reading package lists... Done
Reading package lists... Done
Building dependency tree
Reading state information... Done
hwinfo is already the newest version.
grep is already the newest version.
The following packages were automatically installed and are no longer required:
linux-
Use 'apt-get autoremove' to remove them.
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
*-network
description: Wireless interface
product: Realtek Semiconductor Co., Ltd.
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:02:00.0
logical name: wlan0
version: 10
serial: 70:f1:a1:d2:24:d2
width: 32 bits
clock: 33MHz
resources: irq:17 ioport:
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:85:00.0
logical name: eth0
version: 02
serial: 1c:c1:de:8d:cc:65
size: 100MB/s
capacity: 100MB/s
width: 64 bits
clock: 33MHz
resources: irq:29 ioport:
0: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: D8:5D:4C:CE:15:B1
pan0 Interface doesn't support scanning.
auto lo
iface lo inet loopback
DISTRIB_ID=Ubuntu
DISTRIB_
DISTRIB_
DISTRIB_
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03)
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03)
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03)
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03)
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03)
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 [8086:294a] (rev 03)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93)
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03)
00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03)
02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. Device [10ec:8171] (rev 10)
85:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 03f0:231d Hewlett-Packard
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 04f2:b1ac Chicony Electronics Co., Ltd
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
H/W path Device Class Description
=======
/0 bus 1526
/0/a memory 64KiB BIOS
/0/0 processor Pentium(R) Dual-Core CPU T4500
/0/0/1 memory 1MiB L2 cache
/0/0/3 memory 32KiB L1 cache
/0/0/0.1 processor Logical CPU
/0/0/0.2 processor Logical CPU
/0/2 memory 32KiB L1 cache
/0/4 memory 3GiB System Memory
/0/4/0 memory 2GiB SODIMM Synchronous 800 MHz (1.2
/0/4/1 memory 1GiB SODIMM Synchronous 800 MHz (1.2
/0/100 bridge Mobile 4 Series Chipset Memory Contro
/0/100/2 display Mobile 4 Series Chipset Integrated Gr
/0/100/2.1 display Mobile 4 Series Chipset Integrated Gr
/0/100/1a bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1a.1 bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1a.2 bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1a.7 bus 82801I (ICH9 Family) USB2 EHCI Contro
/0/100/1b multimedia 82801I (ICH9 Family) HD Audio Control
/0/100/1c bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.1 bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.1/0 wlan0 network Realtek Semiconductor Co., Ltd.
/0/100/1c.2 bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.4 bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.5 bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.5/0 eth0 network RTL8101E/RTL8102E PCI Express Fast Et
/0/100/1d bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1d.1 bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1d.2 bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1d.7 bus 82801I (ICH9 Family) USB2 EHCI Contro
/0/100/1e bridge 82801 Mobile PCI Bridge
/0/100/1f bridge ICH9M LPC Interface Controller
/0/100/1f.2 scsi0 storage ICH9M/M-E SATA AHCI Controller
/0/100/1f.2/0 /dev/sda disk 320GB Hitachi HTS72503
/0/100/1f.2/0/1 /dev/sda1 volume 289GiB EXT4 volume
/0/100/1f.2/0/2 /dev/sda2 volume 8651MiB Extended partition
/0/100/1f.2/0/2/5 /dev/sda5 volume 8651MiB Linux swap / Solaris partitio
/0/100/1f.2/1 /dev/cdrom disk DVD RW AD-7586H
/1 power PH06047
Linux forrest-laptop 2.6.32-24-generic #42-Ubuntu SMP Fri Aug 20 14:24:04 UTC 2010 i686 GNU/Linux
[ 0.808567] ACPI: No dock devices found.
[ 0.834339] usbcore: registered new interface driver usbfs
[ 0.834339] usbcore: registered new interface driver hub
[ 0.834339] usbcore: registered new device driver usb
[ 0.840018] Switching to clocksource tsc
[ 0.845301] pnp: PnP ACPI: found 11 devices
[ 0.880064] pci 0000:85:00.0: BAR 6: no parent found for of device [0xfffe0000-
[ 0.894145] Firmware did not grant requested _OSC control
[ 0.894165] Firmware did not grant requested _OSC control
[ 0.894181] Firmware did not grant requested _OSC control
[ 0.894197] Firmware did not grant requested _OSC control
[ 0.894213] Firmware did not grant requested _OSC control
[ 0.894243] Firmware did not grant requested _OSC control
[ 0.894259] Firmware did not grant requested _OSC control
[ 0.894275] Firmware did not grant requested _OSC control
[ 0.894290] Firmware did not grant requested _OSC control
[ 0.894305] Firmware did not grant requested _OSC control
[ 0.992308] input: Lid Switch as /devices/
[ 0.992391] ACPI: Lid Switch [LID]
[ 0.998828] Switching to clocksource hpet
[ 1.600105] usb usb1: configuration #1 chosen from 1 choice
[ 1.600130] hub 1-0:1.0: USB hub found
[ 1.620086] usb usb2: configuration #1 chosen from 1 choice
[ 1.620108] hub 2-0:1.0: USB hub found
[ 1.620362] usb usb3: configuration #1 chosen from 1 choice
[ 1.620384] hub 3-0:1.0: USB hub found
[ 1.620618] usb usb4: configuration #1 chosen from 1 choice
[ 1.620640] hub 4-0:1.0: USB hub found
[ 1.620831] usb usb5: configuration #1 chosen from 1 choice
[ 1.620853] hub 5-0:1.0: USB hub found
[ 1.621041] usb usb6: configuration #1 chosen from 1 choice
[ 1.621062] hub 6-0:1.0: USB hub found
[ 1.621262] usb usb7: configuration #1 chosen from 1 choice
[ 1.621286] hub 7-0:1.0: USB hub found
[ 1.621469] usb usb8: configuration #1 chosen from 1 choice
[ 1.621492] hub 8-0:1.0: USB hub found
[ 1.624552] device-mapper: multipath: version 1.1.0 loaded
[ 1.624555] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.627920] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.934438] isapnp: No Plug & Play device found
[ 2.021219] eth0: RTL8102e at 0xf8078000, 1c:c1:de:8d:cc:65, XID 04e00000 IRQ 29
[ 2.056141] usb 1-5: new high speed USB device using ehci_hcd and address 3
[ 2.226814] usb 1-5: configuration #1 chosen from 1 choice
[ 2.340075] usb 2-5: new high speed USB device using ehci_hcd and address 2
[ 2.473558] usb 2-5: configuration #1 chosen from 1 choice
[ 2.480364] usbcore: registered new interface driver usb-storage
[ 2.480371] usb-storage: device found at 2
[ 2.480372] usb-storage: waiting for device to settle before scanning
[ 2.712066] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 2.879414] usb 3-1: configuration #1 chosen from 1 choice
[ 7.480148] usb-storage: device scan complete
[ 8.822849] lp: driver loaded but no devices found
[ 8.904919] rtllib_crypt: registered algorithm 'NULL'
[ 8.904922] rtllib_crypt: registered algorithm 'TKIP'
[ 8.904924] rtllib_crypt: registered algorithm 'CCMP'
[ 8.904925] rtllib_crypt: registered algorithm 'WEP'
[ 8.904974] rtl819xSE 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 8.904982] rtl819xSE 0000:02:00.0: setting latency timer to 64
[ 8.945352] Adapter(8192SE) is found - DeviceID=8171
[ 9.067778] usbcore: registered new interface driver btusb
[ 9.206288] uvcvideo: Found UVC 1.00 device HP Webcam [2 MP Fixed] (04f2:b1ac)
[ 9.264685] input: HP Webcam [2 MP Fixed] as /devices/
[ 9.264781] usbcore: registered new interface driver uvcvideo
[ 11.767750] Console: switching to colour frame buffer device 170x48
[ 13.850650] rtl819xSE 0000:02:00.0: firmware: requesting RTL8192SE/
[ 14.040085] rtl8192_
[ 14.049779] ===>rtllib_
[ 14.060088] ADDRCONF(
[ 14.062522] r8169: eth0: link up
[ 14.062551] r8169: eth0: link up
[ 24.648028] eth0: no IPv6 routers present
[ 37.244990] rtl8192_
[ 37.459068] usb 2-5: USB disconnect, address 2
[ 67.246221] rtl8192_
[ 107.247465] rtl8192_
[ 137.003643] rtl8192_
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 802.11bgn Nickname:
Bit Rate:135 Mb/s
Retry:on RTS thr:off Fragment thr:off
Power Management:off
Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
pan0 no wireless extensions.
/etc/modprobe.
/etc/modprobe.
28: PCI 200.0: 0282 WLAN controller
[Created at pci.318]
UDI: /org/freedeskto
Unique ID: y9sn.LijBSGb8FsA
Parent ID: qTvu.8Makl3iDVc3
SysFS ID: /devices/
SysFS BusID: 0000:02:00.0
Hardware Class: network
Model: "Realtek WLAN controller"
Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
Device: pci 0x8171
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x1467
Revision: 0x10
Driver: "rtl819xSE"
Driver Modules: "r8192se_pci"
Device File: wlan0
Features: WLAN
I/O Ports: 0x7000-0x7fff (rw)
Memory Range: 0xd8800000-
IRQ: 17 (951 events)
HW Address: 70:f1:a1:d2:24:d2
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472
WLAN bitrates: 1 2 5.5 11 6 9 12 18 24 36 48 54
WLAN encryption modes: TKIP CCMP
WLAN authentication modes: open wpa-psk wpa-eap
Module Alias: "pci:v000010ECd
Driver Info #0:
Driver Status: r8192se_pci is active
Driver Activation Cmd: "modprobe r8192se_pci"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #17 (PCI bridge)
29: PCI 8500.0: 0200 Ethernet controller
[Created at pci.318]
UDI: /org/freedeskto
Unique ID: rBUF.oOAmgPb8C5F
Parent ID: HnsE.Gg7kbdesig6
SysFS ID: /devices/
SysFS BusID: 0000:85:00.0
Hardware Class: network
Model: "Realtek RTL8101E/RTL8102E PCI Express Fast Ethernet controller"
Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
Device: pci 0x8136 "RTL8101E/RTL8102E PCI Express Fast Ethernet controller"
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x1526
Revision: 0x02
Driver: "r8169"
Driver Modules: "r8169"
Device File: eth0
I/O Ports: 0x2000-0x2fff (rw)
Memory Range: 0xd0410000-
Memory Range: 0xd0400000-
Memory Range: 0xd0420000-
IRQ: 29 (12742 events)
HW Address: 1c:c1:de:8d:cc:65
Link detected: yes
Module Alias: "pci:v000010ECd
Driver Info #0:
Driver Status: r8169 is active
Driver Activation Cmd: "modprobe r8169"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #20 (PCI bridge)
Module Size Used by
binfmt_misc 6587 1
rfcomm 33421 4
sco 7885 2
bridge 45582 0
stp 1655 1 bridge
ppdev 5259 0
bnep 9436 2
l2cap 30624 16 rfcomm,bnep
snd_hda_
snd_hda_codec_idt 51978 0
snd_hda_intel 21941 2
fbcon 35102 71
snd_hda_codec 74201 3 snd_hda_
snd_hwdep 5412 1 snd_hda_codec
tileblit 2031 1 fbcon
snd_pcm_oss 35308 0
snd_mixer_oss 13746 1 snd_pcm_oss
snd_pcm 70662 3 snd_hda_
font 7557 1 fbcon
bitblit 4707 1 fbcon
softcursor 1189 1 bitblit
snd_seq_dummy 1338 0
snd_seq_oss 26726 0
snd_seq_midi 4557 0
snd_rawmidi 19056 1 snd_seq_midi
vga16fb 11385 0
snd_seq_midi_event 6003 2 snd_seq_
snd_seq 47263 6 snd_seq_
vgastate 8961 1 vga16fb
snd_timer 19098 2 snd_pcm,snd_seq
snd_seq_device 5700 5 snd_seq_
joydev 8708 0
snd 54148 17 snd_hda_
i915 285586 3
soundcore 6620 1 snd
drm_kms_helper 29297 1 i915
drm 162409 4 i915,drm_kms_helper
snd_page_alloc 7076 2 snd_hda_
i2c_algo_bit 5028 1 i915
uvcvideo 56990 0
intel_agp 24119 2 i915
video 17375 1 i915
agpgart 31724 2 drm,intel_agp
videodev 34361 1 uvcvideo
output 1871 1 video
btusb 10925 2
v4l1_compat 13251 2 uvcvideo,videodev
psmouse 63245 0
bluetooth 49892 9 rfcomm,
serio_raw 3978 0
r8192se_pci 447966 0
lp 7028 0
parport 32635 2 ppdev,lp
usb_storage 39425 0
ahci 32200 2
r8169 34076 0
mii 4381 1 r8169
* Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0.
Revision history for this message
|
#11 |
Second try: with what i entered
forrest@
[sudo] password for forrest:
Hit http://
Ign http://
Ign http://
Ign http://
Ign http://
Hit http://
Ign http://
Ign http://
Ign http://
Ign http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Ign http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Ign http://
Ign http://
Ign http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Hit http://
Reading package lists... Done
Reading package lists... Done
Building dependency tree
Reading state information... Done
hwinfo is already the newest version.
grep is already the newest version.
The following packages were automatically installed and are no longer required:
linux-
Use 'apt-get autoremove' to remove them.
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
*-network
description: Wireless interface
product: Realtek Semiconductor Co., Ltd.
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:02:00.0
logical name: wlan0
version: 10
serial: 70:f1:a1:d2:24:d2
width: 32 bits
clock: 33MHz
resources: irq:17 ioport:
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:85:00.0
logical name: eth0
version: 02
serial: 1c:c1:de:8d:cc:65
size: 100MB/s
capacity: 100MB/s
width: 64 bits
clock: 33MHz
resources: irq:29 ioport:
0: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wlan0 Scan completed :
Cell 01 - Address: D8:5D:4C:CE:15:B1
pan0 Interface doesn't support scanning.
auto lo
iface lo inet loopback
DISTRIB_ID=Ubuntu
DISTRIB_
DISTRIB_
DISTRIB_
00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07)
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)
00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07)
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03)
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03)
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03)
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03)
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03)
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 [8086:294a] (rev 03)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93)
00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03)
00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03)
02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. Device [10ec:8171] (rev 10)
85:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02)
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 03f0:231d Hewlett-Packard
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 04f2:b1ac Chicony Electronics Co., Ltd
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
H/W path Device Class Description
=======
/0 bus 1526
/0/a memory 64KiB BIOS
/0/0 processor Pentium(R) Dual-Core CPU T4500
/0/0/1 memory 1MiB L2 cache
/0/0/3 memory 32KiB L1 cache
/0/0/0.1 processor Logical CPU
/0/0/0.2 processor Logical CPU
/0/2 memory 32KiB L1 cache
/0/4 memory 3GiB System Memory
/0/4/0 memory 2GiB SODIMM Synchronous 800 MHz (1.2
/0/4/1 memory 1GiB SODIMM Synchronous 800 MHz (1.2
/0/100 bridge Mobile 4 Series Chipset Memory Contro
/0/100/2 display Mobile 4 Series Chipset Integrated Gr
/0/100/2.1 display Mobile 4 Series Chipset Integrated Gr
/0/100/1a bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1a.1 bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1a.2 bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1a.7 bus 82801I (ICH9 Family) USB2 EHCI Contro
/0/100/1b multimedia 82801I (ICH9 Family) HD Audio Control
/0/100/1c bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.1 bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.1/0 wlan0 network Realtek Semiconductor Co., Ltd.
/0/100/1c.2 bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.4 bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.5 bridge 82801I (ICH9 Family) PCI Express Port
/0/100/1c.5/0 eth0 network RTL8101E/RTL8102E PCI Express Fast Et
/0/100/1d bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1d.1 bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1d.2 bus 82801I (ICH9 Family) USB UHCI Control
/0/100/1d.7 bus 82801I (ICH9 Family) USB2 EHCI Contro
/0/100/1e bridge 82801 Mobile PCI Bridge
/0/100/1f bridge ICH9M LPC Interface Controller
/0/100/1f.2 scsi0 storage ICH9M/M-E SATA AHCI Controller
/0/100/1f.2/0 /dev/sda disk 320GB Hitachi HTS72503
/0/100/1f.2/0/1 /dev/sda1 volume 289GiB EXT4 volume
/0/100/1f.2/0/2 /dev/sda2 volume 8651MiB Extended partition
/0/100/1f.2/0/2/5 /dev/sda5 volume 8651MiB Linux swap / Solaris partitio
/0/100/1f.2/1 /dev/cdrom disk DVD RW AD-7586H
/1 power PH06047
Linux forrest-laptop 2.6.32-24-generic #42-Ubuntu SMP Fri Aug 20 14:24:04 UTC 2010 i686 GNU/Linux
[ 0.808567] ACPI: No dock devices found.
[ 0.834339] usbcore: registered new interface driver usbfs
[ 0.834339] usbcore: registered new interface driver hub
[ 0.834339] usbcore: registered new device driver usb
[ 0.840018] Switching to clocksource tsc
[ 0.845301] pnp: PnP ACPI: found 11 devices
[ 0.880064] pci 0000:85:00.0: BAR 6: no parent found for of device [0xfffe0000-
[ 0.894145] Firmware did not grant requested _OSC control
[ 0.894165] Firmware did not grant requested _OSC control
[ 0.894181] Firmware did not grant requested _OSC control
[ 0.894197] Firmware did not grant requested _OSC control
[ 0.894213] Firmware did not grant requested _OSC control
[ 0.894243] Firmware did not grant requested _OSC control
[ 0.894259] Firmware did not grant requested _OSC control
[ 0.894275] Firmware did not grant requested _OSC control
[ 0.894290] Firmware did not grant requested _OSC control
[ 0.894305] Firmware did not grant requested _OSC control
[ 0.992308] input: Lid Switch as /devices/
[ 0.992391] ACPI: Lid Switch [LID]
[ 0.998828] Switching to clocksource hpet
[ 1.600105] usb usb1: configuration #1 chosen from 1 choice
[ 1.600130] hub 1-0:1.0: USB hub found
[ 1.620086] usb usb2: configuration #1 chosen from 1 choice
[ 1.620108] hub 2-0:1.0: USB hub found
[ 1.620362] usb usb3: configuration #1 chosen from 1 choice
[ 1.620384] hub 3-0:1.0: USB hub found
[ 1.620618] usb usb4: configuration #1 chosen from 1 choice
[ 1.620640] hub 4-0:1.0: USB hub found
[ 1.620831] usb usb5: configuration #1 chosen from 1 choice
[ 1.620853] hub 5-0:1.0: USB hub found
[ 1.621041] usb usb6: configuration #1 chosen from 1 choice
[ 1.621062] hub 6-0:1.0: USB hub found
[ 1.621262] usb usb7: configuration #1 chosen from 1 choice
[ 1.621286] hub 7-0:1.0: USB hub found
[ 1.621469] usb usb8: configuration #1 chosen from 1 choice
[ 1.621492] hub 8-0:1.0: USB hub found
[ 1.624552] device-mapper: multipath: version 1.1.0 loaded
[ 1.624555] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.627920] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.934438] isapnp: No Plug & Play device found
[ 2.021219] eth0: RTL8102e at 0xf8078000, 1c:c1:de:8d:cc:65, XID 04e00000 IRQ 29
[ 2.056141] usb 1-5: new high speed USB device using ehci_hcd and address 3
[ 2.226814] usb 1-5: configuration #1 chosen from 1 choice
[ 2.340075] usb 2-5: new high speed USB device using ehci_hcd and address 2
[ 2.473558] usb 2-5: configuration #1 chosen from 1 choice
[ 2.480364] usbcore: registered new interface driver usb-storage
[ 2.480371] usb-storage: device found at 2
[ 2.480372] usb-storage: waiting for device to settle before scanning
[ 2.712066] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 2.879414] usb 3-1: configuration #1 chosen from 1 choice
[ 7.480148] usb-storage: device scan complete
[ 8.822849] lp: driver loaded but no devices found
[ 8.904919] rtllib_crypt: registered algorithm 'NULL'
[ 8.904922] rtllib_crypt: registered algorithm 'TKIP'
[ 8.904924] rtllib_crypt: registered algorithm 'CCMP'
[ 8.904925] rtllib_crypt: registered algorithm 'WEP'
[ 8.904974] rtl819xSE 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 8.904982] rtl819xSE 0000:02:00.0: setting latency timer to 64
[ 8.945352] Adapter(8192SE) is found - DeviceID=8171
[ 9.067778] usbcore: registered new interface driver btusb
[ 9.206288] uvcvideo: Found UVC 1.00 device HP Webcam [2 MP Fixed] (04f2:b1ac)
[ 9.264685] input: HP Webcam [2 MP Fixed] as /devices/
[ 9.264781] usbcore: registered new interface driver uvcvideo
[ 11.767750] Console: switching to colour frame buffer device 170x48
[ 13.850650] rtl819xSE 0000:02:00.0: firmware: requesting RTL8192SE/
[ 14.040085] rtl8192_
[ 14.049779] ===>rtllib_
[ 14.060088] ADDRCONF(
[ 14.062522] r8169: eth0: link up
[ 14.062551] r8169: eth0: link up
[ 24.648028] eth0: no IPv6 routers present
[ 37.244990] rtl8192_
[ 37.459068] usb 2-5: USB disconnect, address 2
[ 67.246221] rtl8192_
[ 107.247465] rtl8192_
[ 137.003643] rtl8192_
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 802.11bgn Nickname:
Bit Rate:135 Mb/s
Retry:on RTS thr:off Fragment thr:off
Power Management:off
Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
pan0 no wireless extensions.
/etc/modprobe.
/etc/modprobe.
28: PCI 200.0: 0282 WLAN controller
[Created at pci.318]
UDI: /org/freedeskto
Unique ID: y9sn.LijBSGb8FsA
Parent ID: qTvu.8Makl3iDVc3
SysFS ID: /devices/
SysFS BusID: 0000:02:00.0
Hardware Class: network
Model: "Realtek WLAN controller"
Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
Device: pci 0x8171
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x1467
Revision: 0x10
Driver: "rtl819xSE"
Driver Modules: "r8192se_pci"
Device File: wlan0
Features: WLAN
I/O Ports: 0x7000-0x7fff (rw)
Memory Range: 0xd8800000-
IRQ: 17 (951 events)
HW Address: 70:f1:a1:d2:24:d2
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472
WLAN bitrates: 1 2 5.5 11 6 9 12 18 24 36 48 54
WLAN encryption modes: TKIP CCMP
WLAN authentication modes: open wpa-psk wpa-eap
Module Alias: "pci:v000010ECd
Driver Info #0:
Driver Status: r8192se_pci is active
Driver Activation Cmd: "modprobe r8192se_pci"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #17 (PCI bridge)
29: PCI 8500.0: 0200 Ethernet controller
[Created at pci.318]
UDI: /org/freedeskto
Unique ID: rBUF.oOAmgPb8C5F
Parent ID: HnsE.Gg7kbdesig6
SysFS ID: /devices/
SysFS BusID: 0000:85:00.0
Hardware Class: network
Model: "Realtek RTL8101E/RTL8102E PCI Express Fast Ethernet controller"
Vendor: pci 0x10ec "Realtek Semiconductor Co., Ltd."
Device: pci 0x8136 "RTL8101E/RTL8102E PCI Express Fast Ethernet controller"
SubVendor: pci 0x103c "Hewlett-Packard Company"
SubDevice: pci 0x1526
Revision: 0x02
Driver: "r8169"
Driver Modules: "r8169"
Device File: eth0
I/O Ports: 0x2000-0x2fff (rw)
Memory Range: 0xd0410000-
Memory Range: 0xd0400000-
Memory Range: 0xd0420000-
IRQ: 29 (12742 events)
HW Address: 1c:c1:de:8d:cc:65
Link detected: yes
Module Alias: "pci:v000010ECd
Driver Info #0:
Driver Status: r8169 is active
Driver Activation Cmd: "modprobe r8169"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #20 (PCI bridge)
Module Size Used by
binfmt_misc 6587 1
rfcomm 33421 4
sco 7885 2
bridge 45582 0
stp 1655 1 bridge
ppdev 5259 0
bnep 9436 2
l2cap 30624 16 rfcomm,bnep
snd_hda_
snd_hda_codec_idt 51978 0
snd_hda_intel 21941 2
fbcon 35102 71
snd_hda_codec 74201 3 snd_hda_
snd_hwdep 5412 1 snd_hda_codec
tileblit 2031 1 fbcon
snd_pcm_oss 35308 0
snd_mixer_oss 13746 1 snd_pcm_oss
snd_pcm 70662 3 snd_hda_
font 7557 1 fbcon
bitblit 4707 1 fbcon
softcursor 1189 1 bitblit
snd_seq_dummy 1338 0
snd_seq_oss 26726 0
snd_seq_midi 4557 0
snd_rawmidi 19056 1 snd_seq_midi
vga16fb 11385 0
snd_seq_midi_event 6003 2 snd_seq_
snd_seq 47263 6 snd_seq_
vgastate 8961 1 vga16fb
snd_timer 19098 2 snd_pcm,snd_seq
snd_seq_device 5700 5 snd_seq_
joydev 8708 0
snd 54148 17 snd_hda_
i915 285586 3
soundcore 6620 1 snd
drm_kms_helper 29297 1 i915
drm 162409 4 i915,drm_kms_helper
snd_page_alloc 7076 2 snd_hda_
i2c_algo_bit 5028 1 i915
uvcvideo 56990 0
intel_agp 24119 2 i915
video 17375 1 i915
agpgart 31724 2 drm,intel_agp
videodev 34361 1 uvcvideo
output 1871 1 video
btusb 10925 2
v4l1_compat 13251 2 uvcvideo,videodev
psmouse 63245 0
bluetooth 49892 9 rfcomm,
serio_raw 3978 0
r8192se_pci 447966 0
lp 7028 0
parport 32635 2 ppdev,lp
usb_storage 39425 0
ahci 32200 2
r8169 34076 0
mii 4381 1 r8169
* Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0.
Revision history for this message
|
#12 |
sorry for the double post
Revision history for this message
|
#13 |
Please try the solution from Roger Liang at HP at the bottom of the following page:
https:/
You can get the RTL8192SE driver
rtl8192se_
from the Realtek site at the following URL: