b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found -> Wireless Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02) not working on Acer Aspire 5003 WLMi in Ubuntu 9.10

Asked by Ali

I loaded UBUNTU and it did not connected my wireless modem. I created a wireless connection with name and password but it did not work and I think the reason is it does not see the wireless card on my laptop (Acer Aspire 5003 WLMi )because it's lamp is continuously off. A few days ago I have tried Puppy Linux also.It saw my wireless card from the beginning . I think some driver is necessary for Ubuntu to see my wireless card.

Question information

Language:
English Edit question
Status:
Solved
For:
Ubuntu gnome-nettool Edit question
Assignee:
No assignee Edit question
Solved by:
Mark Rijckenberg
Solved:
Last query:
Last reply:
Revision history for this message
k4rsten (karsten-kulach) said :
#1

can you please post your result from 'ifconfig' and the content of the file '/etc/network/interfaces'?

Revision history for this message
Mark Rijckenberg (markrijckenberg) said :
#2

Hi,

Please first connect your network card to the wireless router using an ethernet cable (also known as a LAN cable).

In order to gather essential troubleshooting information about your wireless card, please follow this procedure:

Step 1: Open Terminal from "Applications->Accessories->Terminal"

Step 2: Please copy-paste the following command from the https://answers.launchpad.net/ubuntu website in Firefox into the Linux Terminal. Do NOT copy-paste from the Email message into the Terminal, as that will only copy PART of the command. The command STARTS with the word sudo and ENDS with the word restart. So please copy-paste the ENTIRE command below from Firefox into a Terminal, press <enter>, then enter password when sudo asks for password, then press enter again.

Tip: If you have a wheel mouse or 3 button mouse you do not need to type commands into the Terminal. Highlight the command written on the page. Move your cursor anywhere in the Terminal and press the wheel or middle button. Automatic Copy and paste! No spelling mistakes! No Typos! No other errors!

sudo lshw -C network; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -short; uname -a; dmesg | grep ound; dmesg | grep b43; dmesg | grep wl; dmesg | grep witch; iwconfig; grep b43 /etc/modprobe.d/*; grep wl /etc/modprobe.d/*; sudo /etc/init.d/networking restart

Step 3: Please post results (copy/paste terminal output) on this thread. The troubleshooters here need to see the full Terminal output from running the above command.

Regards,

Mark

Revision history for this message
Ali (acoruh) said :
#3

On Sun, Mar 21, 2010 at 11:48 AM, Mark Rijckenberg <
<email address hidden>> wrote:

> Your question #105026 on Ubuntu changed:
> https://answers.launchpad.net/ubuntu/+question/105026
>
> Mark Rijckenberg requested for more information:
> Hi,
>
>
> Please first connect your network card to the wireless router using an
> ethernet cable (also known as a LAN cable).
>
>
> In order to gather essential troubleshooting information about your
> wireless card, please follow this procedure:
>
>
> Step 1: Open Terminal from "Applications->Accessories->Terminal"
>
>
> Step 2: Please copy-paste the following command from the
> https://answers.launchpad.net/ubuntu website in Firefox into the Linux
> Terminal. Do NOT copy-paste from the Email message into the Terminal, as
> that will only copy PART of the command. The command STARTS with the word
> sudo and ENDS with the word restart. So please copy-paste the ENTIRE command
> below from Firefox into a Terminal, press <enter>, then enter password when
> sudo asks for password, then press enter again.
>
>
> Tip: If you have a wheel mouse or 3 button mouse you do not need to type
> commands into the Terminal. Highlight the command written on the page. Move
> your cursor anywhere in the Terminal and press the wheel or middle button.
> Automatic Copy and paste! No spelling mistakes! No Typos! No other errors!
>
> sudo lshw -C network; sudo iwlist scanning; cat /etc/network/interfaces;
> cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -short; uname -a;
> dmesg | grep ound; dmesg | grep b43; dmesg | grep wl; dmesg | grep
> witch; iwconfig; grep b43 /etc/modprobe.d/*; grep wl /etc/modprobe.d/*;
> sudo /etc/init.d/networking restart
>
>
> Step 3: Please post results (copy/paste terminal output) on this thread.
> The troubleshooters here need to see the full Terminal output from running
> the above command.
>
> Regards,
>
> Mark
>

Hi mark,
I have done your advices and the report is copied below.
Regards

> ali@ali-laptop:~$ sudo lshw -C network; sudo iwlist scanning; cat
> /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw
> -short; uname -a; dmesg | grep ound; dmesg | grep b43; dmesg | grep wl;
> dmesg | grep witch; iwconfig; grep b43 /etc/modprobe.d/*; grep wl
> /etc/modprobe.d/*; sudo /etc/init.d/networking restart
> [sudo] password for ali:
> Sorry, try again.
> [sudo] password for ali:
> *-network:0
> description: Ethernet interface
> product: SiS900 PCI Fast Ethernet
> vendor: Silicon Integrated Systems [SiS]
> physical id: 4
> bus info: pci@0000:00:04.0
> logical name: eth0
> version: 91
> serial: 00:16:36:34:dc:6e
> size: 100MB/s
> capacity: 100MB/s
> width: 32 bits
> clock: 33MHz
> capabilities: pm bus_master cap_list rom ethernet physical tp mii
> 10bt 10bt-fd 100bt 100bt-fd autonegotiation
> configuration: autonegotiation=on broadcast=yes driver=sis900
> driverversion=v1.08.10 Apr. 2 2006 duplex=full ip=192.168.2.5 latency=173
> link=yes maxlatency=11 mingnt=52 multicast=yes port=MII speed=100MB/s
> resources: irq:19 ioport:1800(size=256) memory:e2005000-e2005fff
> memory:48000000-4801ffff(prefetchable)
> *-network:1
> description: Network controller
> product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller
> vendor: Broadcom Corporation
> physical id: b
> bus info: pci@0000:00:0b.0
> version: 02
> width: 32 bits
> clock: 33MHz
> capabilities: bus_master
> configuration: driver=b43-pci-bridge latency=64
> resources: irq:17 memory:e2000000-e2001fff
> *-network DISABLED
> description: Wireless interface
> physical id: 1
> logical name: wlan0
> serial: 00:16:ce:36:d2:34
> capabilities: ethernet physical wireless
> configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg
> lo Interface doesn't support scanning.
>
> eth0 Interface doesn't support scanning.
>
> wlan0 Interface doesn't support scanning : Network is down
>
> auto lo
> iface lo inet loopback
>
> DISTRIB_ID=Ubuntu
> DISTRIB_RELEASE=9.10
> DISTRIB_CODENAME=karmic
> DISTRIB_DESCRIPTION="Ubuntu 9.10"
> 00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 760/M760 Host
> [1039:0760] (rev 03)
> 00:01.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] SG86C202
> [1039:0002]
> 00:02.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS963 [MuTIOL
> Media IO] [1039:0963] (rev 25)
> 00:02.1 SMBus [0c05]: Silicon Integrated Systems [SiS] SiS961/2 SMBus
> Controller [1039:0016]
> 00:02.5 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 [IDE]
> [1039:5513]
> 00:02.6 Modem [0703]: Silicon Integrated Systems [SiS] AC'97 Modem
> Controller [1039:7013] (rev a0)
> 00:02.7 Multimedia audio controller [0401]: Silicon Integrated Systems
> [SiS] AC'97 Sound Controller [1039:7012] (rev a0)
> 00:03.0 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1
> Controller [1039:7001] (rev 0f)
> 00:03.1 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1
> Controller [1039:7001] (rev 0f)
> 00:03.2 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 2.0
> Controller [1039:7002]
> 00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] SiS900
> PCI Fast Ethernet [1039:0900] (rev 91)
> 00:06.0 CardBus bridge [0607]: Texas Instruments PCI1510 PC card Cardbus
> Controller [104c:ac56]
> 00:0b.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce
> One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
> 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8
> [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
> 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8
> [Athlon64/Opteron] Address Map [1022:1101]
> 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8
> [Athlon64/Opteron] DRAM Controller [1022:1102]
> 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8
> [Athlon64/Opteron] Miscellaneous Control [1022:1103]
> 01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS]
> 661/741/760 PCI/AGP or 662/761Gx PCIE VGA Display Adapter [1039:6330]
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 003 Device 002: ID 045e:0083 Microsoft Corp. Basic Optical Mouse
> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> H/W path Device Class Description
> =========================================================
> system Aspire 5000
> /0 bus Lugano M
> /0/0 memory 101KiB BIOS
> /0/4 processor AMD Turion(tm) 64 Mobile Tec
> /0/4/8 memory 128KiB L1 cache
> /0/4/9 memory 512KiB L2 cache
> /0/10 memory System Memory
> /0/1 memory
> /0/1/0 memory 512MiB DIMM DDR Synchronous
> /0/2 memory
> /0/2/0 memory 512MiB DIMM DDR Synchronous
> /0/3 memory
> /0/5 memory
> /0/100 bridge 760/M760 Host
> /0/100/1 bridge SG86C202
> /0/100/1/0 display 661/741/760 PCI/AGP or 662/7
> /0/100/2 bridge SiS963 [MuTIOL Media IO]
> /0/100/2.1 bus SiS961/2 SMBus Controller
> /0/100/2.5 scsi0 storage 5513 [IDE]
> /0/100/2.5/0 /dev/sda disk 80GB WDC WD800UE-22HC
> /0/100/2.5/0/1 /dev/sda1 volume 2996MiB Windows FAT volume
> /0/100/2.5/0/2 /dev/sda2 volume 29GiB Windows FAT volume
> /0/100/2.5/0/3 /dev/sda3 volume 42GiB Extended partition
> /0/100/2.5/0/3/5 /dev/sda5 volume 27GiB HPFS/NTFS partition
> /0/100/2.5/0/3/6 /dev/sda6 volume 13GiB Linux filesystem parti
> /0/100/2.5/0/3/7 /dev/sda7 volume 674MiB Linux swap / Solaris
> /0/100/2.5/1 /dev/cdrom1 disk UJ-840D
> /0/100/2.6 communication AC'97 Modem Controller
> /0/100/2.7 multimedia AC'97 Sound Controller
> /0/100/3 bus USB 1.1 Controller
> /0/100/3.1 bus USB 1.1 Controller
> /0/100/3.2 bus USB 2.0 Controller
> /0/100/4 eth0 network SiS900 PCI Fast Ethernet
> /0/100/6 bridge PCI1510 PC card Cardbus Cont
> /0/100/b network BCM4318 [AirForce One 54g] 8
> /0/101 bridge K8 [Athlon64/Opteron] HyperT
> /0/102 bridge K8 [Athlon64/Opteron] Addres
> /0/103 bridge K8 [Athlon64/Opteron] DRAM C
> /0/104 bridge K8 [Athlon64/Opteron] Miscel
> /1 wlan0 network Wireless interface
> Linux ali-laptop 2.6.31-20-generic #58-Ubuntu SMP Fri Mar 12 05:23:09 UTC
> 2010 i686 GNU/Linux
> [ 0.000000] found SMP MP-table at [c00f7fd0] f7fd0
> [ 0.110079] ACPI: No dock devices found.
> [ 0.123219] pnp: PnP ACPI: found 8 devices
> [ 1.157903] isapnp: No Plug & Play device found
> [ 1.172146] hub 1-0:1.0: USB hub found
> [ 1.228098] hub 2-0:1.0: USB hub found
> [ 1.284097] hub 3-0:1.0: USB hub found
> [ 1.288707] device-mapper: multipath round-robin: version 1.0.0 loaded
> [ 1.290591] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology
> ML-32 processors (1 cpu cores) (version 2.20.00)
> [ 1.290978] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
> [ 1.913755] ssb: Sonics Silicon Backplane found on PCI device
> 0000:00:0b.0
> [ 1.918445] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at
> address 13.
> [ 1.924031] 0000:00:04.0: Using transceiver found at address 13 as
> default
> [ 19.739754] yenta_cardbus 0000:00:06.0: CardBus bridge found [1025:0083]
> [ 19.757455] lp: driver loaded but no devices found
> [ 20.464346] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
> [ 20.821251] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
> [ 20.821257] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
> [ 20.903040] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
> [ 20.903046] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
> [ 1.823104] b43-pci-bridge 0000:00:0b.0: PCI INT A -> GSI 17 (level,
> low) -> IRQ 17
> [ 20.464346] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
> [ 20.552434] Registered led device: b43-phy0::tx
> [ 20.552453] Registered led device: b43-phy0::rx
> [ 20.552471] Registered led device: b43-phy0::radio
> [ 20.726464] b43 ssb0:0: firmware: requesting b43/ucode5.fw
> [ 20.810504] b43 ssb0:0: firmware: requesting b43-open/ucode5.fw
> [ 20.821251] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
> [ 20.821257] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
> [ 20.821261] b43-phy0 ERROR: You must go to
> http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and
> download the correct firmware for this driver version. Please carefully read
> all instructions on this website.
> [ 20.880252] b43 ssb0:0: firmware: requesting b43/ucode5.fw
> [ 20.892498] b43 ssb0:0: firmware: requesting b43-open/ucode5.fw
> [ 20.903040] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found
> [ 20.903046] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found
> [ 20.903050] b43-phy0 ERROR: You must go to
> http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and
> download the correct firmware for this driver version. Please carefully read
> all instructions on this website.
> [ 0.020766] SMP alternatives: switching to UP code
> [ 0.076780] ACPI: EC: non-query interrupt received, switching to
> interrupt mode
> [ 0.794701] input: Lid Switch as
> /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
> [ 0.797472] ACPI: Lid Switch [LID]
> [ 0.801752] Switched to high resolution mode on CPU 0
> lo no wireless extensions.
>
> eth0 no wireless extensions.
>
> wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated
> Tx-Power=0 dBm
> Retry long limit:7 RTS thr:off Fragment thr:off
> Power Management:off
>
> /etc/modprobe.d/blacklist.conf:# replaced by b43 and ssb.
> /etc/modprobe.d/blacklist-watchdog.conf:blacklist twl4030_wdt
> * Reconfiguring network interfaces...
> Ignoring unknown interface eth0=eth0.
> [ OK ]
> ali@ali-laptop:~$
>
>

Revision history for this message
Best Mark Rijckenberg (markrijckenberg) said :
#4

Hi,

Please first connect your network card to the wireless router using an ethernet cable (also known as a LAN cable).

The error "b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found or load failed" should mean that b43-fwcutter is not installed yet on your pc. And that means that the Broadcom firmware for your wireless card is not loaded or installed yet.

Please proceed with the following commands:

sudo aptitude update
sudo aptitude install b43-fwcutter

b43-fwcutter exists in the Ubuntu repositories, but you will need a working wired Internet connection in Ubuntu in order to locate it and install it.

The only way to do that - in your case - is to connect the pc to the wireless router using a LAN cable, instead of using wireless.

Regards,

Mark

Revision history for this message
Ali (acoruh) said :
#5

Thanks Mark Rijckenberg, that solved my question.

Revision history for this message
Elise Nelson (mackeronee) said :
#6

I am having this same problem....Gateway MA2A; Broadcom BCM4318; Ubuntu 10.04 LTS.

I initially ran
"sudo lshw -C network; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo ishw -short; uname -a; dmesg | grep ound; dmesg | grep b43; dmesg | grep wl; dmesg | grep witch; iwconfig; grep b43 /etc/modprobe.d/*; grep wl /etc/modprobe.d/*; sudo /etc/init.d/networking restart
"

but I received the "b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found" ERROR so I started with the aptitude update.

And, I'm still receiving errors. I know that it is reading as "Disabled", but have been unable to figure out how to change this. The Light that indicates WiFi is on is lit.

Thanks in advance for any help!

ubuntu@ubuntu:~$ sudo aptitude update

Ign cdrom://Ubuntu 10.04 LTS _Lucid Lynx_ - Release i386 (20100429)/ lucid/main Translation-en_US

Ign cdrom://Ubuntu 10.04 LTS _Lucid Lynx_ - Release i386 (20100429)/ lucid/restricted Translation-en_US

Get:1 http://archive.ubuntu.com lucid Release.gpg [189B]

Ign http://archive.ubuntu.com/ubuntu/ lucid/main Translation-en_US

Get:2 http://security.ubuntu.com lucid-security Release.gpg [189B]

Ign http://security.ubuntu.com/ubuntu/ lucid-security/main Translation-en_US

Ign http://archive.ubuntu.com/ubuntu/ lucid/restricted Translation-en_US

Get:3 http://archive.ubuntu.com lucid-updates Release.gpg [189B]

Ign http://archive.ubuntu.com/ubuntu/ lucid-updates/main Translation-en_US

Ign http://archive.ubuntu.com/ubuntu/ lucid-updates/restricted Translation-en_US

Get:4 http://archive.ubuntu.com lucid Release [57.2kB]

Ign http://security.ubuntu.com/ubuntu/ lucid-security/restricted Translation-en_US

Get:5 http://security.ubuntu.com lucid-security Release [32.5kB]

Get:6 http://archive.ubuntu.com lucid-updates Release [38.5kB]

Get:7 http://security.ubuntu.com lucid-security/main Packages [5,309B]

Get:8 http://archive.ubuntu.com lucid/main Packages [1,386kB]

Get:9 http://security.ubuntu.com lucid-security/restricted Packages [14B]

Get:10 http://security.ubuntu.com lucid-security/main Sources [2,164B]

Get:11 http://security.ubuntu.com lucid-security/restricted Sources [14B]

Get:12 http://archive.ubuntu.com lucid/restricted Packages [6,208B]

Get:13 http://archive.ubuntu.com lucid/main Sources [659kB]

Get:14 http://archive.ubuntu.com lucid/restricted Sources [3,775B]

Get:15 http://archive.ubuntu.com lucid-updates/main Packages [156kB]

Get:16 http://archive.ubuntu.com lucid-updates/restricted Packages [2,102B]

Get:17 http://archive.ubuntu.com lucid-updates/main Sources [61.6kB]

Get:18 http://archive.ubuntu.com lucid-updates/restricted Sources [737B]

Fetched 2,412kB in 7s (310kB/s)

Reading package lists... Done

Current status: 108 updates [+108], 15 new [+15].

ubuntu@ubuntu:~$ sudo aptitude install b43-fwcutter

Reading package lists... Done

Building dependency tree

Reading state information... Done

Reading extended state information

Initializing package states... Done

No packages will be installed, upgraded, or removed.

0 packages upgraded, 0 newly installed, 0 to remove and 108 not upgraded.

Need to get 0B of archives. After unpacking 0B will be used.

Writing extended state information... Done

Reading package lists... Done

Building dependency tree

Reading state information... Done

Reading extended state information

Initializing package states... Done

ubuntu@ubuntu:~$ sudo lshw -C network; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo ishw -short; uname -a; dmesg | grep ound; dmesg | grep b43; dmesg | grep wl; dmesg | grep witch; iwconfig; grep b43 /etc/modprobe.d/*; grep wl /etc/modprobe.d/*; sudo /etc/init.d/networking restart

  *-network

       description: Ethernet interface

       product: 88E8036 PCI-E Fast Ethernet Controller

       vendor: Marvell Technology Group Ltd.

       physical id: 0

       bus info: pci@0000:02:00.0

       logical name: eth0

       version: 10

       serial: 00:e0:b8:9a:42:6b

       size: 100MB/s

       capacity: 100MB/s

       width: 64 bits

       clock: 33MHz

       capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation

       configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.25 duplex=full firmware=N/A ip=192.168.1.71 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s

       resources: irq:25 memory:b4000000-b4003fff ioport:3000(size=256)

  *-network

       description: Network controller

       product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller

       vendor: Broadcom Corporation

       physical id: 4

       bus info: pci@0000:06:04.0

       version: 02

       width: 32 bits

       clock: 33MHz

       capabilities: bus_master

       configuration: driver=b43-pci-bridge latency=32

       resources: irq:17 memory:b8004000-b8005fff

  *-network DISABLED

       description: Wireless interface

       physical id: 1

       logical name: wlan0

       serial: 00:14:a5:48:b7:ab

       capabilities: ethernet physical wireless

       configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg

lo Interface doesn't support scanning.

eth0 Interface doesn't support scanning.

wlan0 Interface doesn't support scanning : Network is down

auto lo

iface lo inet loopback

DISTRIB_ID=Ubuntu

DISTRIB_RELEASE=10.04

DISTRIB_CODENAME=lucid

DISTRIB_DESCRIPTION="Ubuntu 10.04 LTS"

00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 04)

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 04)

00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 04)

00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 04)

00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 04)

00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 04)

00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 04)

00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 04)

00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 04)

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d4)

00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [8086:266e] (rev 04)

00:1e.3 Modem [0703]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller [8086:266d] (rev 04)

00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 04)

00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller [8086:266f] (rev 04)

00:1f.3 SMBus [0c05]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller [8086:266a] (rev 04)

02:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8036 PCI-E Fast Ethernet Controller [11ab:4351] (rev 10)

06:04.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)

06:09.0 CardBus bridge [0607]: Texas Instruments PCIxx21/x515 Cardbus Controller [104c:8031]

06:09.2 FireWire (IEEE 1394) [0c00]: Texas Instruments OHCI Compliant IEEE 1394 Host Controller [104c:8032]

06:09.3 Mass storage controller [0180]: Texas Instruments PCIxx21 Integrated FlashMedia Controller [104c:8033]

06:09.4 SD Host controller [0805]: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller [104c:8034]

Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

Bus 001 Device 002: ID 0781:5406 SanDisk Corp. Cruzer Micro 1/2/4GB Flash Drive

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

sudo: ishw: command not found

Linux ubuntu 2.6.32-21-generic #32-Ubuntu SMP Fri Apr 16 08:10:02 UTC 2010 i686 GNU/Linux

[ 0.104147] ACPI: No dock devices found.

[ 0.130115] pnp: PnP ACPI: found 9 devices

[ 3.344480] hub 1-0:1.0: USB hub found

[ 3.345624] hub 2-0:1.0: USB hub found

[ 3.347669] hub 3-0:1.0: USB hub found

[ 3.352682] hub 4-0:1.0: USB hub found

[ 3.353507] hub 5-0:1.0: USB hub found

[ 3.363530] device-mapper: multipath round-robin: version 1.0.0 loaded

[ 3.372283] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found

[ 3.747101] isapnp: No Plug & Play device found

[ 4.124125] usb-storage: device found at 2

[ 4.336695] ssb: Sonics Silicon Backplane found on PCI device 0000:06:04.0

[ 68.734371] sdhci-pci 0000:06:09.4: SDHCI controller found [104c:8034] (rev 0)

[ 68.944775] yenta_cardbus 0000:06:09.0: CardBus bridge found [107b:0365]

[ 69.109796] b43-phy0: Broadcom 4318 WLAN found (core revision 9)

[ 69.485498] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found

[ 69.485505] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found

[ 69.541003] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found

[ 69.541010] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found

[ 70.859035] lp: driver loaded but no devices found

[ 1767.717647] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found

[ 1767.717655] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found

[ 1767.800225] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found

[ 1767.800242] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found

[ 4.165417] b43-pci-bridge 0000:06:04.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17

[ 69.109796] b43-phy0: Broadcom 4318 WLAN found (core revision 9)

[ 69.346115] Registered led device: b43-phy0::tx

[ 69.346138] Registered led device: b43-phy0::rx

[ 69.346161] Registered led device: b43-phy0::radio

[ 69.440082] b43 ssb0:0: firmware: requesting b43/ucode5.fw

[ 69.467859] b43 ssb0:0: firmware: requesting b43-open/ucode5.fw

[ 69.485498] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found

[ 69.485505] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found

[ 69.485510] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.

[ 69.508242] b43 ssb0:0: firmware: requesting b43/ucode5.fw

[ 69.531400] b43 ssb0:0: firmware: requesting b43-open/ucode5.fw

[ 69.541003] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found

[ 69.541010] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found

[ 69.541015] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.

[ 1767.700064] b43 ssb0:0: firmware: requesting b43/ucode5.fw

[ 1767.706866] b43 ssb0:0: firmware: requesting b43-open/ucode5.fw

[ 1767.717647] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found

[ 1767.717655] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found

[ 1767.717659] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.

[ 1767.780086] b43 ssb0:0: firmware: requesting b43/ucode5.fw

[ 1767.786153] b43 ssb0:0: firmware: requesting b43-open/ucode5.fw

[ 1767.800225] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found

[ 1767.800242] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found

[ 1767.800247] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website.

[ 0.021181] SMP alternatives: switching to UP code

[ 0.124016] Switching to clocksource tsc

[ 3.237158] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2

[ 3.237585] ACPI: Lid Switch [LID]

[ 3.242175] Switching to clocksource hpet

[ 5.150477] Console: switching to colour frame buffer device 160x50

lo no wireless extensions.

eth0 no wireless extensions.

wlan0 IEEE 802.11bg ESSID:off/any

          Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm

          Retry long limit:7 RTS thr:off Fragment thr:off

          Power Management:off

/etc/modprobe.d/blacklist.conf:# replaced by b43 and ssb.

/etc/modprobe.d/blacklist-watchdog.conf:blacklist twl4030_wdt

 * Reconfiguring network interfaces... [ OK ]

ubuntu@ubuntu:~$

Revision history for this message
Mark Rijckenberg (markrijckenberg) said :
#7

@Elise: this thread is already in the "solved" state. Please a new, separate question using this link:

https://answers.launchpad.net/ubuntu/+source/gnome-nettool/+addquestion