Bus 003 Device 002: ID 12d1:1001 Huawei Technologies Co., Ltd. E620 USB Modem - How to connect internet using my Huawei wireless modem 153.6K? I am usin BSNL highspeed(Dial up) Internet

Hi,

In order to gather essential troubleshooting information about your Huawei modem, please follow this procedure:

Step 1: Open Terminal from "Applications->Accessories->Terminal"

Step 2: Please copy-paste the following command from the https://answers.launchpad.net/ubuntu website in Firefox into the Linux Terminal. Do NOT copy-paste from the Email message into the Terminal, as that will only copy PART of the command. The command STARTS with the word sudo and ENDS with the word restart. So please copy-paste the ENTIRE command below from Firefox into a Terminal, press <enter>, then enter password when sudo asks for password, then press enter again.

sudo lshw -C network; sudo iwlist scanning; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; sudo lshw -C usb; uname -a; dmesg | grep ound; dmesg | grep b43; dmesg | grep iwl; iwconfig; sudo /etc/init.d/networking restart

Step 3: Please post results (copy/paste terminal output) on this thread

Regards,

Mark

Hi mark,
thanks for the guidance.
I followed to ur step 2 above
the result is as follows:

 *-network
       description: Ethernet interface
       product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: pci@0000:01:00.0
       logical name: eth0
       version: 01
       serial: 00:24:8c:cb:de:f9
       size: 10MB/s capacity: 100MB/s
       width: 64 bits
       clock: 33MH
       capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no module=r8169 multicast=yes port=MII speed=10MB/s
  *-network DISABLED
      description: Ethernet interface
       physical id: 1
       logical name: pan0
       serial: 9a:31:4f:4b:10:fe
       capabilities: ethernet physical
       configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
pan0 Interface doesn't support scanning.
auto lo
iface lo inet loopback
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=9.04
DISTRIB_CODENAME=jaunty
DISTRIB_DESCRIPTION="Ubuntu 9.04"
00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller [8086:29c0] (rev 10)
00:02.0 VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express Integrated Graphics Controller [8086:29c2] (rev 10)
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 01)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 01)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 01)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 01)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 01)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 01)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01)
00:1f.2 IDE interface [0101]: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller [8086:27c0] (rev 01)
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 01)
01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 01)
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 12d1:1001 Huawei Technologies Co., Ltd. E620 USB Modem
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Linux ubuntu 2.6.28-11-generic #42-Ubuntu SMP Fri Apr 17 01:57:59 UTC 2009 i686 GNU/Linux [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working it around.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.416540] ACPI: No dock devices found.
[ 0.446171] pnp: PnP ACPI: found 16 devices
[ 1.021549] pcieport-driver 0000:00:1c.0: found MSI capability
[ 1.021675] pcieport-driver 0000:00:1c.1: found MSI capability

so let me guide what to do after that.
D. Swain

Oh Mark,
Some of the lines were left which I am adding as follows;

[ 1.377502] isapnp: No Plug & Play device found
[ 2.252144] hub 1-0:1.0: USB hub found
[ 2.252410] hub 2-0:1.0: USB hub found
[ 2.252608] hub 3-0:1.0: USB hub found
[ 2.252802] hub 4-0:1.0: USB hub found
[ 2.253000] hub 5-0:1.0: USB hub found
[ 2.268358] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.270138] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 7.908396] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x0860)
[ 8.428616] psmouse serio1: ID: 10 00 64<6>lp: driver loaded but no devices found
[ 38.097028] UDF-fs: No VRS found
lo no wireless extensions.
eth0 no wireless extensions.
pan0 no wireless extensions.
 * Reconfiguring network interfaces... [OK]

I am new to ubuntu, so please guide me accordingly

Please try this procedure:

http://reliancewireless.wordpress.com/2009/05/10/connecting-reliance-netconnect-broadband-on-jaunty-jackalope/

If that does not work, try the backup procedure here (using wvdial instead of NetworkManager):

http://buzypi.in/2009/07/11/getting-reliance-huawei-usb-data-card-to-work-in-ubuntu-9-04-jaunty/

If the Huawei USB modem does not work using NetworkManager in Ubuntu 9.04, then I suggest installing Ubuntu 8.10 from a LiveCD session and then use NetworkManager in Ubuntu 8.10 to handle the broadband USB modem connection.

If that does not work, please send full output of following Terminal commands in Ubuntu 8.10, after following all the previous procedures:

tail -f200 /var/log/messages
cat /etc/wvdial.conf
sudo wvdial cdma

this is wot happened wen i entered the first set of comands

*-network
       description: Ethernet interface
       product: 88E8039 PCI-E Fast Ethernet Controller
       vendor: Marvell Technology Group Ltd.
       physical id: 0
       bus info: pci@0000:02:00.0
       logical name: eth0
       version: 15
       serial: 00:1d:72:0e:1d:2f
       size: 100MB/s
       capacity: 100MB/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.20 duplex=full firmware=N/A ip=10.1.1.4 latency=0 link=yes module=sky2 multicast=yes port=twisted pair speed=100MB/s
  *-network UNCLAIMED
       description: Ethernet controller
       product: AR242x 802.11abg Wireless PCI Express Adapter
       vendor: Atheros Communications Inc.
       physical id: 0
       bus info: pci@0000:04:00.0
       version: 01
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress msix cap_list
       configuration: latency=0
lo Interface doesn't support scanning.

eth0 Interface doesn't support scanning.

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface

DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=8.04
DISTRIB_CODENAME=hardy
DISTRIB_DESCRIPTION="Ubuntu 8.04.3 LTS"
00:00.0 Host bridge [0600]: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub [8086:2a00] (rev 03)
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a02] (rev 03)
00:02.1 Display controller [0380]: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller [8086:2a03] (rev 03)
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 03)
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 03)
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 03)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 03)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 [8086:2841] (rev 03)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 [8086:2843] (rev 03)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 03)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev f3)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller [8086:2815] (rev 03)
00:1f.1 IDE interface [0101]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller [8086:2850] (rev 03)
00:1f.2 SATA controller [0106]: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller [8086:2829] (rev 03)
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 03)
02:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8039 PCI-E Fast Ethernet Controller [11ab:4353] (rev 15)
04:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
Bus 007 Device 001: ID 0000:0000
Bus 006 Device 001: ID 0000:0000
Bus 005 Device 002: ID 12d1:1001 Huawei Technologies Co., Ltd. E620 USB Modem
Bus 005 Device 001: ID 0000:0000
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Linux jack 2.6.24-24-generic #1 SMP Fri Sep 18 16:49:39 UTC 2009 i686 GNU/Linux
[ 0.000000] found SMP MP-table at 000f7e10
[ 13.030976] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 13.370440] pnp: PnP ACPI: found 10 devices
[ 14.170762] assign_interrupt_mode Found MSI capability
[ 14.171010] assign_interrupt_mode Found MSI capability
[ 14.171254] assign_interrupt_mode Found MSI capability
[ 14.525161] isapnp: No Plug & Play device found
[ 14.576388] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 16.253281] hub 1-0:1.0: USB hub found
[ 16.357291] hub 2-0:1.0: USB hub found
[ 16.461107] hub 3-0:1.0: USB hub found
[ 16.564944] hub 4-0:1.0: USB hub found
[ 16.668798] hub 5-0:1.0: USB hub found
[ 16.792401] hub 6-0:1.0: USB hub found
[ 16.912202] hub 7-0:1.0: USB hub found
[ 29.739177] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
[ 32.280862] lp: driver loaded but no devices found
[ 34.025517] No dock devices found.
[ 35.233723] apm: BIOS not found.
lo no wireless extensions.

eth0 no wireless extensions.

 * Reconfiguring network interfaces... [ OK ]

and this is wot happened wen i entered the last set of comands

andrew@jack:~$ sudo wvdial cdma
--> WvDial: Internet dialer version 1.60
--> Warning: section [Dialer cdma] does not exist in wvdial.conf.
--> Cannot open /dev/modem: No such file or directory
--> Cannot open /dev/modem: No such file or directory
--> Cannot open /dev/modem: No such file or directory

can u help me with the E620 usb modem?