AR242X wireless turning off during boot of Asus x50r laptop
AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01) not working in Ubuntu 8.10
I dont get wireless to work on a asus x50r whit Atheros 802.11abg wireless card, could someone pleace help,..
Question information
- Language:
- English Edit question
- Status:
- Answered
- For:
- Ubuntu Edit question
- Assignee:
- No assignee Edit question
- Last query:
- Last reply:
Revision history for this message
|
#1 |
Try with madwifi drivers
1. install dependencies
linux-restricte
lspci | grep Wireless
sudo ifconfig ath0 down
sudo rmmod ath_pci
wget http://
sudo tar -zxvf madwifi-
make
sudo make install
sudo gedit /etc/modules add in the end "ath_pci"
sudo reboot
Revision history for this message
|
#2 |
Sorry is
sudo tar -zxvf madwifi-
Revision history for this message
|
#3 |
got this message after the make command
make: *** No targets specified and no makefile found. Stop.
Revision history for this message
|
#4 |
Go to http://
Revision history for this message
|
#5 |
Revision history for this message
|
#6 |
the machine recognises the card, but I dont get any signal from the router. It works fine on the other laptopp so its not the router. If I run iwconfig I get,..
marit@
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:""
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
What should I do, and thanks for the help
Revision history for this message
|
#7 |
Hi,
Please first connect your network card to the wireless router using a LAN cable.
Then please follow this procedure (in order to gather troubleshooting info):
Step 1: Open Terminal from "Applications-
Terminal"
Step 2: Run the following commands (copy-paste each line below to the Terminal then hit <enter> after each line)
sudo aptitude install hwinfo
hwinfo --netcard
sudo iwlist scanning
sudo lshw -C network
lspci -nn
lsusb
uname -a
dmesg | grep ound
dmesg | grep witch
iwconfig
Step 3: Please post results (copy/paste terminal output from each command) on this thread
Regards,
Mark
Revision history for this message
|
#8 |
marit@marit-
[sudo] password for marit:
Leser pakkelister ... Ferdig
Skaper oversikt over avhengighetsforhold
Leser tilstandsinform
Reading extended state information
Initializing package states ... Ferdig
The following NEW packages will be installed:
hwinfo libhd14{a}
0 packages upgraded, 2 newly installed, 0 to remove and 0 not upgraded.
Need to get 717kB of archives. After unpacking 1978kB will be used.
Do you want to continue? [Y/n/?] y
Writing extended state information ... Ferdig
Get:1 http://
Get:2 http://
Fetched 717kB in 1s (485kB/s)
Velger den tidligere fravalgte pakken libhd14.
(Leser database ... 173735 filer og kataloger er installerte.)
Pakker ut libhd14 (fra .../libhd14_
Velger den tidligere fravalgte pakken hwinfo.
Pakker ut hwinfo (fra .../hwinfo_
Behandler utløsere for man-db ...
Setter opp libhd14 (14.19-2ubuntu1) ...
Setter opp hwinfo (14.19-2ubuntu1) ...
Behandler utløsere for libc6 ...
ldconfig deferred processing now taking place
Leser pakkelister ... Ferdig
Skaper oversikt over avhengighetsforhold
Leser tilstandsinform
Reading extended state information
Initializing package states ... Ferdig
Writing extended state information ... Ferdig
marit@marit-
07: PCI 600.0: 0200 Ethernet controller
[Created at pci.310]
UDI: /org/freedeskto
Unique ID: rBUF.KzmrTqfccB0
Parent ID: H0_h.0XeE0ctGI+6
SysFS ID: /devices/
SysFS BusID: 0000:06:00.0
Hardware Class: network
Model: "Attansic L2 100 Mbit Ethernet Adapter"
Vendor: pci 0x1969 "Attansic Technology Corp."
Device: pci 0x2048 "L2 100 Mbit Ethernet Adapter"
SubVendor: pci 0x1043 "ASUSTeK Computer Inc."
SubDevice: pci 0x1415
Revision: 0xa0
Driver: "atl2"
Driver Modules: "atl2"
Device File: eth0
Memory Range: 0xfeac0000-
Memory Range: 0xfeaa0000-
IRQ: 219 (2435 events)
HW Address: 00:1d:60:07:f0:c3
Link detected: yes
Module Alias: "pci:v00001969d
Driver Info #0:
Driver Status: atl2 is active
Driver Activation Cmd: "modprobe atl2"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #23 (PCI bridge)
08: PCI 200.0: 0282 WLAN controller
[Created at pci.310]
UDI: /org/freedeskto
Unique ID: y9sn.oTCoeEt5Tw6
Parent ID: 8otl._hlk2XIeEf7
SysFS ID: /devices/
SysFS BusID: 0000:02:00.0
Hardware Class: network
Model: "Atheros AR242x 802.11abg Wireless PCI Express Adapter"
Vendor: pci 0x168c "Atheros Communications, Inc."
Device: pci 0x001c "AR242x 802.11abg Wireless PCI Express Adapter"
SubVendor: pci 0x1a3b
SubDevice: pci 0x1026
Revision: 0x01
Driver: "ath5k"
Driver Modules: "ath5k"
Device File: wlan0
Features: WLAN
Memory Range: 0xfa9f0000-
IRQ: 16 (2066 events)
HW Address: 00:15:af:3f:b8:1c
Link detected: no
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "pci:v0000168Cd
Driver Info #0:
Driver Status: ath_pci is active
Driver Activation Cmd: "modprobe ath_pci"
Driver Info #1:
Driver Status: ath5k is active
Driver Activation Cmd: "modprobe ath5k"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #25 (PCI bridge)
marit@marit-
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wmaster0 Interface doesn't support scanning.
wlan0 No scan results
marit@marit-
*-network
description: Wireless interface
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:02:00.0
logical name: wmaster0
version: 01
serial: 00:15:af:3f:b8:1c
width: 64 bits
clock: 33MHz
*-network
description: Ethernet interface
product: L2 100 Mbit Ethernet Adapter
vendor: Attansic Technology Corp.
physical id: 0
bus info: pci@0000:06:00.0
logical name: eth0
version: a0
serial: 00:1d:60:07:f0:c3
size: 10MB/s
capacity: 100MB/s
width: 64 bits
clock: 33MHz
marit@marit-
00:00.0 Host bridge [0600]: ATI Technologies Inc Device [1002:5a31] (rev 01)
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f]
00:04.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a36]
00:05.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a37]
00:06.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a38]
00:07.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a39]
00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380]
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0) [1002:4387]
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1) [1002:4388]
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2) [1002:4389]
00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3) [1002:438a]
00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4) [1002:438b]
00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller (EHCI) [1002:4386]
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 13)
00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c]
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge [1002:438d]
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384]
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RC410 [Radeon Xpress 200M] [1002:5a62]
02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
06:00.0 Ethernet controller [0200]: Attansic Technology Corp. L2 100 Mbit Ethernet Adapter [1969:2048] (rev a0)
marit@marit-
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0bda:0116 Realtek Semiconductor Corp. Mass Storage Device
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
marit@marit-
Linux marit-laptop 2.6.27-11-generic #1 SMP Thu Jan 29 19:24:39 UTC 2009 i686 GNU/Linux
marit@marit-
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working it around.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 1.129180] pnp: PnP ACPI: found 11 devices
[ 2.992193] pcieport-driver 0000:00:04.0: found MSI capability
[ 2.992522] pcieport-driver 0000:00:05.0: found MSI capability
[ 2.992832] pcieport-driver 0000:00:06.0: found MSI capability
[ 2.993158] pcieport-driver 0000:00:07.0: found MSI capability
[ 3.348964] isapnp: No Plug & Play device found
[ 3.455558] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 4.980523] No dock devices found.
[ 5.116530] ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
[ 5.128481] hub 1-0:1.0: USB hub found
[ 5.983796] usb-storage: device found at 2
[ 7.012975] hub 2-0:1.0: USB hub found
[ 7.177090] hub 3-0:1.0: USB hub found
[ 7.341110] hub 4-0:1.0: USB hub found
[ 7.505290] hub 5-0:1.0: USB hub found
[ 7.669439] hub 6-0:1.0: USB hub found
[ 21.602930] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[ 24.592024] lp: driver loaded but no devices found
[ 30.037579] apm: BIOS not found.
marit@marit-
[ 1.204534] checking if image is initramfs.
[ 1.684083] Switched to high resolution mode on CPU 0
[ 3.978854] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 19.021395] input: Lid Switch as /devices/
[ 19.024291] ACPI: Lid Switch [LID]
marit@marit-
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:""
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
thanks for the help
Revision history for this message
|
#9 |
Hi,
# Please try this Atheros driver installation procedure:
# First under System/
# Then from a terminal type (press enter key after each line)
sudo aptitude update
sudo aptitude install build-essential subversion
cd ~
mkdir madwifi
cd madwifi
svn co https:/
cd madwifi-
make
sudo make install
sudo gedit /etc/modules
# Now add the Atheros kernel module ath_pci to the list of modules to be automatically loaded at boot by adding
ath_pci
# to the end of the /etc/modules file. (Gedit editor automatically opens)
sudo gedit /etc/modprobe.
# Now add the following 3 lines to the end of the /etc/modprobe.
ndiswrapper
ath5k
ath9k
Now you can reboot and it should work.
Hope this helps,
Regards,
Mark
Revision history for this message
|
#10 |
#hi Mark, and thanks for the help, it still does not work but I get signal level and link qvality parameters witch i havent before:)
marit@marit-
lo no wireless extensions.
eth0 no wireless extensions.
wifi0 no wireless extensions.
ath0 IEEE 802.11g ESSID:"" Nickname:""
Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1
Retry:off RTS thr:off Fragment thr:off
Power Management:off
Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
marit@marit-
#when ;:::disable both the Atheros HAL and the Atheros wireless thing and then reboot;;;..it was only the atheros wireless thing to disable.
#Got the feal the compiling did not go to well so i copy pasted it in here.
marit@marit-
marit@marit-
mkdir: cannot create directory `madwifi': File exists
marit@marit-
marit@marit-
mkdir: cannot create directory `madwifi': File exists
marit@marit-
marit@marit-
Fetching external item into 'madwifi-
Checked out external at revision 3952.
Checked out revision 3952.
marit@marit-
marit@marit-
Checking requirements... ok.
Checking kernel configuration... ok.
make -C /lib/modules/
make[1]: Entering directory `/usr/src/
Building modules, stage 2.
MODPOST 14 modules
make[1]: Leaving directory `/usr/src/
make -C ./tools all || exit 1
make[1]: Entering directory `/home/
for d in ath_info; do \
make -C $d || exit 1; \
done
make[2]: Entering directory `/home/
make[2]: Nothing to be done for `all'.
make[2]: Leaving directory `/home/
make[1]: Leaving directory `/home/
marit@marit-
Checking requirements... ok.
Checking kernel configuration... ok.
make -C /lib/modules/
make[1]: Entering directory `/usr/src/
Building modules, stage 2.
MODPOST 14 modules
make[1]: Leaving directory `/usr/src/
sh scripts/
for i in ath/ ath_hal/ ath_rate/ net80211/; do \
make -C $i install || exit 1; \
done
make[1]: Entering directory `/home/
test -d //lib/modules/
install -m 0644 ath_pci.ko //lib/modules/
make[1]: Leaving directory `/home/
make[1]: Entering directory `/home/
test -d //lib/modules/
install -m 0644 ath_hal.ko //lib/modules/
make[1]: Leaving directory `/home/
make[1]: Entering directory `/home/
for i in amrr/ onoe/ sample/ minstrel/; do \
make -C $i install || exit 1; \
done
make[2]: Entering directory `/home/
test -d //lib/modules/
install -m 0644 ath_rate_amrr.ko //lib/modules/
make[2]: Leaving directory `/home/
make[2]: Entering directory `/home/
test -d //lib/modules/
install -m 0644 ath_rate_onoe.ko //lib/modules/
make[2]: Leaving directory `/home/
make[2]: Entering directory `/home/
test -d //lib/modules/
install -m 0644 ath_rate_sample.ko //lib/modules/
make[2]: Leaving directory `/home/
make[2]: Entering directory `/home/
test -d //lib/modules/
install -m 0644 ath_rate_
make[2]: Leaving directory `/home/
make[1]: Leaving directory `/home/
make[1]: Entering directory `/home/
test -d //lib/modules/
for i in wlan.o wlan_wep.o wlan_tkip.o wlan_ccmp.o wlan_acl.o wlan_xauth.o wlan_scan_sta.o wlan_scan_ap.o; do \
f=`basename $i .o`; \
install -m 0644 $f.ko //lib/modules/
done
make[1]: Leaving directory `/home/
(export KMODPATH=
make -C ./tools all || exit 1
make[1]: Entering directory `/home/
for d in ath_info; do \
make -C $d || exit 1; \
done
make[2]: Entering directory `/home/
make[2]: Nothing to be done for `all'.
make[2]: Leaving directory `/home/
make[1]: Leaving directory `/home/
make -C ./tools install || exit 1
make[1]: Entering directory `/home/
for d in ath_info; do \
make -C $d || exit 1; \
done
make[2]: Entering directory `/home/
make[2]: Nothing to be done for `all'.
make[2]: Leaving directory `/home/
install -d /usr/local/bin
for i in athstats 80211stats athkey athchans athctrl athdebug 80211debug wlanconfig wpakey; do \
install $i /usr/local/bin/$i; \
strip /usr/local/bin/$i; \
done
install -d /usr/local/man/man8
install -m 0644 man/*.8 /usr/local/man/man8
install ../scripts/
for d in ath_info; do \
make -C $d install || exit 1; \
done
make[2]: Entering directory `/home/
install -d /usr/local/bin
install -m 755 ath_info /usr/local/bin
install -d /usr/local/
install -m 644 ath_info.8 /usr/local/
make[2]: Leaving directory `/home/
make[1]: Leaving directory `/home/
marit@marit-
#Then I added the stuff to the gedit lists,went ok, restarted and still no wireless working. What can I do to get I right, thanks for the help so far and pleace continue helping me to get it working.
Frode
#I runned the information recquest agan in case you need it
marit@marit-
07: PCI 600.0: 0200 Ethernet controller
[Created at pci.310]
UDI: /org/freedeskto
Unique ID: rBUF.KzmrTqfccB0
Parent ID: H0_h.0XeE0ctGI+6
SysFS ID: /devices/
SysFS BusID: 0000:06:00.0
Hardware Class: network
Model: "Attansic L2 100 Mbit Ethernet Adapter"
Vendor: pci 0x1969 "Attansic Technology Corp."
Device: pci 0x2048 "L2 100 Mbit Ethernet Adapter"
SubVendor: pci 0x1043 "ASUSTeK Computer Inc."
SubDevice: pci 0x1415
Revision: 0xa0
Driver: "atl2"
Driver Modules: "atl2"
Device File: eth0
Memory Range: 0xfeac0000-
Memory Range: 0xfeaa0000-
IRQ: 219 (2781 events)
HW Address: 00:1d:60:07:f0:c3
Link detected: yes
Module Alias: "pci:v00001969d
Driver Info #0:
Driver Status: atl2 is active
Driver Activation Cmd: "modprobe atl2"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #23 (PCI bridge)
08: PCI 200.0: 0282 WLAN controller
[Created at pci.310]
UDI: /org/freedeskto
Unique ID: xFhm.oTCoeEt5Tw6
Parent ID: 8otl._hlk2XIeEf7
SysFS ID: /devices/
SysFS BusID: 0000:02:00.0
Hardware Class: network
Model: "Atheros AR242x 802.11abg Wireless PCI Express Adapter"
Vendor: pci 0x168c "Atheros Communications, Inc."
Device: pci 0x001c "AR242x 802.11abg Wireless PCI Express Adapter"
SubVendor: pci 0x1a3b
SubDevice: pci 0x1026
Revision: 0x01
Driver: "ath_pci"
Driver Modules: "ath_pci"
Device File: ath0
Features: WLAN
Memory Range: 0xfa9f0000-
IRQ: 16 (2363 events)
HW Address: 00:15:af:3f:b8:1c
Link detected: yes
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462
WLAN encryption modes: WEP40 WEP104 WEP128 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "pci:v0000168Cd
Driver Info #0:
Driver Status: ath_pci is active
Driver Activation Cmd: "modprobe ath_pci"
Driver Info #1:
Driver Status: ath5k is not active
Driver Activation Cmd: "modprobe ath5k"
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #25 (PCI bridge)
marit@marit-
[sudo] password for marit:
Sorry, try again.
[sudo] password for marit:
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wifi0 Interface doesn't support scanning.
ath0 No scan results
marit@marit-
*-network
description: Wireless interface
product: AR242x 802.11abg Wireless PCI Express Adapter
vendor: Atheros Communications Inc.
physical id: 0
bus info: pci@0000:02:00.0
logical name: wifi0
version: 01
serial: 00:15:af:3f:b8:1c
width: 64 bits
clock: 33MHz
*-network
description: Ethernet interface
product: L2 100 Mbit Ethernet Adapter
vendor: Attansic Technology Corp.
physical id: 0
bus info: pci@0000:06:00.0
logical name: eth0
version: a0
serial: 00:1d:60:07:f0:c3
size: 10MB/s
capacity: 100MB/s
width: 64 bits
clock: 33MHz
marit@marit-
00:00.0 Host bridge [0600]: ATI Technologies Inc Device [1002:5a31] (rev 01)
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f]
00:04.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a36]
00:05.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a37]
00:06.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a38]
00:07.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a39]
00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380]
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0) [1002:4387]
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1) [1002:4388]
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2) [1002:4389]
00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3) [1002:438a]
00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4) [1002:438b]
00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller (EHCI) [1002:4386]
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 13)
00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c]
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge [1002:438d]
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384]
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RC410 [Radeon Xpress 200M] [1002:5a62]
02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
06:00.0 Ethernet controller [0200]: Attansic Technology Corp. L2 100 Mbit Ethernet Adapter [1969:2048] (rev a0)
marit@marit-
Bus 006 Device 002: ID 0bda:0116 Realtek Semiconductor Corp. Mass Storage Device
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
marit@marit-
Linux marit-laptop 2.6.27-11-generic #1 SMP Thu Jan 29 19:24:39 UTC 2009 i686 GNU/Linux
marit@marit-
[ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working it around.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.584930] pnp: PnP ACPI: found 11 devices
[ 1.435679] pcieport-driver 0000:00:04.0: found MSI capability
[ 1.435861] pcieport-driver 0000:00:05.0: found MSI capability
[ 1.436033] pcieport-driver 0000:00:06.0: found MSI capability
[ 1.436273] pcieport-driver 0000:00:07.0: found MSI capability
[ 1.791280] isapnp: No Plug & Play device found
[ 1.844670] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.567815] No dock devices found.
[ 2.640324] hub 1-0:1.0: USB hub found
[ 2.804419] hub 2-0:1.0: USB hub found
[ 3.072443] hub 3-0:1.0: USB hub found
[ 3.237249] hub 4-0:1.0: USB hub found
[ 3.400208] hub 5-0:1.0: USB hub found
[ 5.108648] ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
[ 5.121317] hub 6-0:1.0: USB hub found
[ 5.616388] usb-storage: device found at 2
[ 17.725789] lp: driver loaded but no devices found
[ 18.443636] wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip 7.0, Radio 10.2)
[ 22.953108] apm: BIOS not found.
marit@marit-
[ 1.132555] Switched to high resolution mode on CPU 1
[ 1.136072] Switched to high resolution mode on CPU 0
[ 2.101585] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 15.057350] input: Lid Switch as /devices/
[ 15.059312] ACPI: Lid Switch [LID]
[ 18.410180] MadWifi: ath_attach: Switching rfkill capability off.
marit@marit-
lo no wireless extensions.
eth0 no wireless extensions.
wifi0 no wireless extensions.
ath0 IEEE 802.11g ESSID:"" Nickname:""
Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1
Retry:off RTS thr:off Fragment thr:off
Power Management:off
Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
marit@marit-
Revision history for this message
|
#11 |
Hi,
Try disabling encryption on the wireless router and enabling SSID broadcasting on the router. These are options you need to set on the wireless router itself using a webinterface.
Also try connecting to your wireless router via wifi using a different pc . See if that works.
If you can access the wireless router using the wireless connection on a different pc, then I recommend reinstalling Ubuntu 8.10 from a LiveCD session onto the problematic pc and then following my madwifi compilation instructions, which work perfectly for everybody else who is using the the AR242X wireless chipset.
If the madwifi procedure does not work, this indicates to me that there are already too many driver conflicts on your pc which are getting in our way.
Regards,
Mark
Revision history for this message
|
#12 |
Hi,
Here is the list of previously solved AR242X threads:
Regards,
Mark
Revision history for this message
|
#13 |
Hi,
I found someone with the same model and make of laptop and with the same Atheros chipset. Check out the thread here:
https:/
He got the wireless issue solved by following these instructions:
Regards,
Mark
Can you help with this problem?
Provide an answer of your own, or ask frode for more information if necessary.