Ubuntu

USB pendrive on dapper not recognized.

Asked by peter b

-dapper has latest updates/upgrades installed.

-pendrive is a SanDisk 1GB cruzer mini formatted with fat16 and has data on it.

-PC has scsi hware Tekram dc-390u3w adapter
       with 1 scsi ultra 160 hdd on one of the ultra buses (68 pin) recognized as sda disk-sda1 device (this device is non bootable) and
       a cdrom on the wide (50 pin) bus.

-dapper installed on hda4 -works ok except recognition of the pendrive; particulars follow

-output of ls /dev/sd* => /dev/sda and /dev/sda1

-output of fdisk -l as above but verbose; no additional sd devices but the two above mentioned

-output of lsusb with the pendrive attached

Bus 004 Device 003: ID 0d8d:0105 Promotion & Display Technology, Ltd
Bus 004 Device 002: ID 0c16:0001 Gyration, Inc.
Bus 004 Device 001: ID 0000:0000
Bus 006 Device 001: ID 0000:0000
Bus 005 Device 002: ID 050d:0980 Belkin Components
Bus 005 Device 001: ID 0000:0000
Bus 003 Device 006: ID 06bd:208f AGFA-Gevaert NV SnapScan e50
Bus 003 Device 007: ID 0ace:1211 ZyDAS 802.11b/g USB2 WiFi
Bus 003 Device 003: ID 050d:0224 Belkin Components F5U224 USB 2.0 4-Port Hub
Bus 003 Device 001: ID 0000:0000
Bus 001 Device 005: ID 041e:4003 Creative Technology, Ltd VideoBlaster WebCam Go Plus [W9967CF]
Bus 001 Device 004: ID 03f0:6204 Hewlett-Packard DeskJet 5150c
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 002: ID 047f:0301 Plantronics, Inc.
Bus 002 Device 001: ID 0000:0000

-dmeseg

[17179592.624000] ieee1394: Initialized config rom entry `ip1394'
[17179592.628000] ohci1394: $Rev: 1313 $ Ben Collins <email address hidden>
[17179592.628000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 177
[17179592.652000] usbcore: registered new driver usbfs
[17179592.652000] usbcore: registered new driver hub
[17179592.656000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179592.700000] USB Universal Host Controller Interface driver v2.3
[17179592.772000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[177] MMIO=[dffcf000-dffcf7ff] Max Packet=[2048]
[17179592.772000] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 16 (level, low) -> IRQ 185
[17179592.772000] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[17179592.772000] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
[17179592.772000] ohci_hcd 0000:00:0b.0: irq 185, io mem 0xdffc8000
[17179593.332000] hub 1-0:1.0: USB hub found
[17179593.332000] hub 1-0:1.0: 3 ports detected
[17179593.848000] ACPI: PCI Interrupt 0000:00:0b.1[B] -> GSI 17 (level, low) -> IRQ 169
[17179593.848000] ohci_hcd 0000:00:0b.1: OHCI Host Controller
[17179593.848000] ohci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
[17179593.848000] ohci_hcd 0000:00:0b.1: irq 169, io mem 0xdffc9000
[17179594.152000] usb 1-1: new full speed USB device using ohci_hcd and address 2
[17179594.408000] hub 2-0:1.0: USB hub found
[17179594.408000] hub 2-0:1.0: 2 ports detected
[17179594.408000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00d0035600b1bc50]
[17179594.676000] usb 1-2: new full speed USB device using ohci_hcd and address 3
[17179594.924000] ACPI: PCI Interrupt 0000:00:0b.2[C] -> GSI 18 (level, low) -> IRQ 177
[17179594.924000] ehci_hcd 0000:00:0b.2: EHCI Host Controller
[17179594.948000] ehci_hcd 0000:00:0b.2: new USB bus registered, assigned bus number 3
[17179594.948000] ehci_hcd 0000:00:0b.2: irq 177, io mem 0xdffcef00
[17179594.948000] ehci_hcd 0000:00:0b.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
[17179594.948000] hub 3-0:1.0: USB hub found
[17179594.948000] hub 3-0:1.0: 5 ports detected
[17179595.052000] ACPI: PCI Interrupt 0000:00:11.2[D] -> GSI 11 (level, low) -> IRQ 11
[17179595.052000] uhci_hcd 0000:00:11.2: UHCI Host Controller
[17179595.052000] uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 4
[17179595.052000] uhci_hcd 0000:00:11.2: irq 11, io base 0x0000bc00
[17179595.052000] hub 4-0:1.0: USB hub found
[17179595.052000] hub 4-0:1.0: 2 ports detected
[17179595.156000] ACPI: PCI Interrupt 0000:00:11.3[D] -> GSI 11 (level, low) -> IRQ 11
[17179595.156000] uhci_hcd 0000:00:11.3: UHCI Host Controller
[17179595.156000] uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 5
[17179595.156000] uhci_hcd 0000:00:11.3: irq 11, io base 0x0000c000
[17179595.156000] hub 5-0:1.0: USB hub found
[17179595.156000] hub 5-0:1.0: 2 ports detected
[17179595.260000] ACPI: PCI Interrupt 0000:00:11.4[D] -> GSI 11 (level, low) -> IRQ 11
[17179595.260000] uhci_hcd 0000:00:11.4: UHCI Host Controller
[17179595.260000] uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 6
[17179595.260000] uhci_hcd 0000:00:11.4: irq 11, io base 0x0000c400
[17179595.260000] hub 6-0:1.0: USB hub found
[17179595.260000] hub 6-0:1.0: 2 ports detected
[17179595.432000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: <email address hidden>
[17179595.636000] usb 3-2: new high speed USB device using ehci_hcd and address 3
[17179595.768000] hub 3-2:1.0: USB hub found
[17179595.768000] hub 3-2:1.0: 4 ports detected
[17179596.064000] Attempting manual resume
[17179596.084000] kjournald starting. Commit interval 5 seconds
[17179596.084000] EXT3-fs: mounted filesystem with ordered data mode.
[17179596.240000] usb 1-1: USB disconnect, address 2
[17179596.544000] usb 1-1: new full speed USB device using ohci_hcd and address 4
[17179596.768000] usb 1-2: USB disconnect, address 3
[17179597.072000] usb 1-2: new full speed USB device using ohci_hcd and address 5
[17179597.548000] usb 4-1: new low speed USB device using uhci_hcd and address 2[17179597.968000] usb 4-2: new full speed USB device using uhci_hcd and address 3
[17179598.612000] usb 5-1: new low speed USB device using uhci_hcd and address 2[17179599.384000] usb 3-2.3: new full speed USB device using ehci_hcd and address 6
[17179599.768000] usb 3-2.4: new high speed USB device using ehci_hcd and address 7
[17179600.180000] usb 2-2: new full speed USB device using ohci_hcd and address 2
[17179602.684000] sd 0:0:6:0: Attached scsi generic sg0 type 0
[17179602.684000] sr 1:0:4:0: Attached scsi generic sg1 type 5
[17179602.720000] sr0: scsi-1 drive
[17179602.720000] sr 1:0:4:0: Attached scsi CD-ROM sr0
[17179605.016000] Linux agpgart interface v0.101 (c) Dave Jones
[17179605.040000] gameport: EMU10K1 is pci0000:00:08.1/gameport0, io 0xec00, speed 1217kHz
[17179605.052000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179605.052000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179605.104000] agpgart: Detected VIA KT266/KY266x/KT333 chipset
[17179605.104000] agpgart: AGP aperture is 32M @ 0xe0000000
[17179605.136000] Floppy drive(s): fd0 is 1.44M, fd1 is 1.2M
[17179605.152000] irda_init()
[17179605.152000] NET: Registered protocol family 23
[17179605.160000] FDC 0 is a post-1991 82077
[17179605.460000] ACPI: PCI Interrupt 0000:00:11.5[C] -> GSI 10 (level, low) -> IRQ 10
[17179605.460000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[17179605.560000] ACPI: PCI Interrupt 0000:00:08.0[A] -> GSI 19 (level, low) -> IRQ 193
[17179605.892000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x03F0 pid 0x6204
[17179605.892000] usbcore: registered new driver usblp
[17179605.892000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[17179605.896000] Linux video capture interface: v1.00
[17179605.908000] w9968cf: V4L driver for W996[87]CF JPEG USB Dual Mode Camera Chip 1:1.33-basic
[17179605.944000] ovcamchip: v2.27 for Linux 2.6 : OV camera chip I2C driver
[17179605.944000] usb 1-2: Creative Labs Video Blaster WebCam Go Plus detected
[17179605.944000] usb 1-2: V4L device registered as /dev/video0
[17179605.948000] parport: PnPBIOS parport detected.
[17179605.948000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[17179606.716000] Real Time Clock Driver v1.12
[17179606.928000] input: PC Speaker as /class/input/input0
[17179606.936000] zd1211 - http://zd1211.ath.cx/ - r83
[17179606.936000] Based on www.zydas.com.tw driver version 2.5.0.0
[17179608.092000] ovcamchip: Camera chip is an OV7620AE
[17179617.052000] usb 1-2: OV7620 image sensor initialized
[17179617.052000] usbcore: registered new driver w9968cf
[17179617.052000] usbcore: registered new driver hiddev
[17179617.504000] usbcore: registered new driver snd-usb-audio
[17179617.596000] usb 3-2.4: reset high speed USB device using ehci_hcd and address 7
[17179617.704000] Release Ver = 4330
[17179617.704000] zd1211:bulk out: wMaxPacketSize = 200
[17179617.704000] zd1211:bulk in: wMaxPacketSize = 200
[17179617.704000] zd1211:interrupt in: wMaxPacketSize = 40
[17179617.704000] zd1211:interrupt in: int_interval = 1
[17179617.704000] zd1211:interrupt out: wMaxPacketSize = 40
[17179617.704000] EEPORM Ver = 4330
[17179617.712000] zd1211:USB Download Boot code success
[17179617.720000] zd1211:MAC address = 00:03:6d:20:b6:ed
[17179617.724000] zd1211:AddrEntryTable = f7d4
[17179617.728000] zd1211:RF_Mode = 0000000d
[17179617.728000] PA type: 0
[17179617.728000] RFMD RF
[17179617.728000] zd1211:Mixed Mode
[17179617.760000] zd1211:AllowedChannel = 000007ff
[17179617.764000] zd1211:LinkLEDn = 200
[17179617.768000] AllowedChannel = 000107ff
[17179617.768000] Region:16
[17179618.120000] zd1205: (exit) zd1205_config, drivers/usb/net/zd1211/zd1205.c line 2601
[17179618.120000] zd1205: (exit) zd1205_init, drivers/usb/net/zd1211/zd1205.c line 8570
[17179618.120000] usbcore: registered new driver zd1211
[17179618.136000] input: ??�???? ?????????????????????????????? as /class/input/input1
[17179618.136000] input: USB HID v1.00 Keyboard [??�???? ??????????????????????????????] on usb-0000:00:11.2-1
[17179618.168000] input: ??�???? ?????????????????????????????? as /class/input/input2
[17179618.168000] input,hiddev96: USB HID v1.00 Mouse [??�???? ??????????????????????????????] on usb-0000:00:11.2-1
[17179618.184000] input: Promotion and Display Technology Ltd VoIPvoice USB Cyberphone K as /class/input/input3
[17179618.184000] input: USB HID v1.00 Device [Promotion and Display Technology Ltd VoIPvoice USB Cyberphone K] on usb-0000:00:11.2-2
[17179618.252000] zd1205: (enter) zd1205_open, drivers/usb/net/zd1211/zd1205.c line 4353
[17179618.300000] zd1205: (exit) zd1205_open, drivers/usb/net/zd1211/zd1205.c line 4436
[17179618.632000] hiddev97: USB HID v1.00 Device [ UPS] on usb-0000:00:11.3-1
[17179618.664000] input: Plantronics Plantronics headset as /class/input/input4
[17179618.664000] input,hiddev98: USB HID v1.00 Device [Plantronics Plantronics headset] on usb-0000:00:0b.1-2
[17179618.664000] usbcore: registered new driver usbhid
[17179618.664000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179618.784000] ts: Compaq touchscreen protocol output
[17179619.300000] lp0: using parport0 (interrupt-driven).
[17179619.308000] zd1211:Mixed Mode
[17179619.332000] NET: Registered protocol family 17
[17179619.352000] sbp2: $Rev: 1306 $ Ben Collins <email address hidden>
[17179619.352000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[17179619.352000] ieee1394: sbp2: Try serialize_io=0 for better performance
[17179619.376000] zd1211:STA_ASSOCIATED with 00:03:6d:f5:01:d4
[17179619.444000] fuse init (API version 7.3)

-any clues anybody? any workarounds or solutions please?

it must be mentioned the fact that same pendrive works on edgy only when hotplugged (edgy up and running); if plugged in and then boot the pendrive appears on desktop but the mouse is disabled. is this normal?

Tx and best regards,
peter b

Question information

Language:
English Edit question
Status:
Solved
For:
Ubuntu Edit question
Assignee:
No assignee Edit question
Solved by:
peter b
Solved:
Last query:
Last reply:
Revision history for this message
Best peter b (b1pete) said : 		#1

looking further into this situation, additional info provided as follows:

- the Belkin usb2 powered hub (5port hub with 4 outgoing, where the pendrive occupies one of the 4) has connected -besides the ZyDas wifi and AGFA identified in the post- also a Samsung laser printer that WASN'T identified by lsusb previously (probably because not turned on).

Today I switched on the laser printer and it was recognized and assigned the address on Bus 003, see below

Bus 004 Device 003: ID 0d8d:0105 Promotion & Display Technology, Ltd
Bus 004 Device 002: ID 0c16:0001 Gyration, Inc.
Bus 004 Device 001: ID 0000:0000
Bus 006 Device 001: ID 0000:0000
Bus 005 Device 002: ID 050d:0980 Belkin Components
Bus 005 Device 001: ID 0000:0000
Bus 003 Device 012: ID 04e8:323a Samsung Electronics Co., Ltd
Bus 003 Device 007: ID 0ace:1211 ZyDAS 802.11b/g USB2 WiFi
Bus 003 Device 006: ID 06bd:208f AGFA-Gevaert NV SnapScan e50
Bus 003 Device 003: ID 050d:0224 Belkin Components F5U224 USB 2.0 4-Port Hub
Bus 003 Device 001: ID 0000:0000
Bus 001 Device 005: ID 041e:4003 Creative Technology, Ltd VideoBlaster WebCam Go Plus [W9967CF]
Bus 001 Device 004: ID 03f0:6204 Hewlett-Packard DeskJet 5150c
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 002: ID 047f:0301 Plantronics, Inc.
Bus 002 Device 001: ID 0000:0000

as shown above there is indeed identified a 5 port hub with 4 ouputs, 3 recognized and one, Device 001 ID 0000:0000 where the pendrive is connected not recognized.

with dapper up and running all 4 devices of the powered hub were disconnected then reconnected one by one and ... success!

the pendrive was assigned a new address so that now Bus 003 has 6 devices, why? miracle, ... I can live with that for now, I'll see what happens in the future. the lsusb output after this exercise is bellow

Bus 004 Device 003: ID 0d8d:0105 Promotion & Display Technology, Ltd
Bus 004 Device 002: ID 0c16:0001 Gyration, Inc.
Bus 004 Device 001: ID 0000:0000
Bus 006 Device 001: ID 0000:0000
Bus 005 Device 002: ID 050d:0980 Belkin Components
Bus 005 Device 001: ID 0000:0000
Bus 003 Device 013: ID 0781:5150 SanDisk Corp. SDCZ2 Cruzer Mini Flash Drive (thin)
Bus 003 Device 012: ID 04e8:323a Samsung Electronics Co., Ltd
Bus 003 Device 007: ID 0ace:1211 ZyDAS 802.11b/g USB2 WiFi
Bus 003 Device 006: ID 06bd:208f AGFA-Gevaert NV SnapScan e50
Bus 003 Device 003: ID 050d:0224 Belkin Components F5U224 USB 2.0 4-Port Hub
Bus 003 Device 001: ID 0000:0000
Bus 001 Device 005: ID 041e:4003 Creative Technology, Ltd VideoBlaster WebCam Go Plus [W9967CF]
Bus 001 Device 004: ID 03f0:6204 Hewlett-Packard DeskJet 5150c
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 002: ID 047f:0301 Plantronics, Inc.
Bus 002 Device 001: ID 0000:0000

I thank you all for patience and help. I'm happy for now.

Regards,
peter b