You're board isn't known (yet) to the driver

As a linux starter I hope this question isn't too simple

I'm running Ubuntu 7.10 and am trying to configure a HVR 4000 DVB card. I've been all over and downloaded drivers but don't actually know how to specify a driver for the dvb card I have. dmesg tells me that I can use "card=<n>" insmod option" and gives me a list of cards I would like to try. But how?

I'm assuming before I load a driver I need to know what hardware I want that driver to apply to. Here's the output of dmesg. What I really would like to know is how to use insmod properly and if successful in finding a driver that works, how I permanently enable it so that it will be loaded on boot.

The device lines are all prefixed with cx88[0]. the line at the end [ 1020.860531] cx25840: Unknown parameter `card' is where i've been fumbling about trying to load a driver.

[dmesg] followed by lspci

[ 0.000000] Linux version 2.6.22-14-server (buildd@king) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Tue Feb 12 03:10:53 UTC 2008 (Ubuntu 2.6.22-14.52-server)
[ 0.000000] Command line: root=/dev/mapper/jollyserver-root ro quiet splash
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000bfde0000 (usable)
[ 0.000000] BIOS-e820: 00000000bfde0000 - 00000000bfde3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000bfde3000 - 00000000bfdf0000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000bfdf0000 - 00000000bfe00000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 785888) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 3200 used
[ 0.000000] end_pfn_map = 1245184
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP signature @ 0xFFFF8100000F71C0 checksum 0
[ 0.000000] ACPI: RSDP 000F71C0, 0014 (r0 RS780 )
[ 0.000000] ACPI: RSDT BFDE3000, 0038 (r1 RS780 GBTUACPI 42302E31 GBTU 1010101)
[ 0.000000] ACPI: FACP BFDE3040, 0074 (r1 RS780 GBTUACPI 42302E31 GBTU 1010101)
[ 0.000000] ACPI: DSDT BFDE30C0, 6550 (r1 RS780 GBTUACPI 1000 MSFT 3000000)
[ 0.000000] ACPI: FACS BFDE0000, 0040
[ 0.000000] ACPI: SSDT BFDE9700, 0206 (r1 PTLTD POWERNOW 1 LTP 1)
[ 0.000000] ACPI: HPET BFDE9940, 0038 (r1 RS780 GBTUACPI 42302E31 GBTU 98)
[ 0.000000] ACPI: MCFG BFDE9980, 003C (r1 RS780 GBTUACPI 42302E31 GBTU 1010101)
[ 0.000000] ACPI: APIC BFDE9640, 0084 (r1 RS780 GBTUACPI 42302E31 GBTU 1010101)
[ 0.000000] Scanning NUMA topology in Northbridge 24
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000130000000
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 785888) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 1245184) 2 entries of 3200 used
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000130000000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1245184
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 785888
[ 0.000000] 0: 1048576 -> 1245184
[ 0.000000] On node 0 totalpages: 982399
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1245 pages reserved
[ 0.000000] DMA zone: 2698 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 767512 pages, LIFO batch:31
[ 0.000000] Normal zone: 2688 pages used for memmap
[ 0.000000] Normal zone: 193920 pages, LIFO batch:31
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] swsusp: Registered nosave memory region: 00000000bfde0000 - 00000000bfde3000
[ 0.000000] swsusp: Registered nosave memory region: 00000000bfde3000 - 00000000bfdf0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000bfdf0000 - 00000000bfe00000
[ 0.000000] swsusp: Registered nosave memory region: 00000000bfe00000 - 00000000e0000000
[ 0.000000] swsusp: Registered nosave memory region: 00000000e0000000 - 00000000f0000000
[ 0.000000] swsusp: Registered nosave memory region: 00000000f0000000 - 00000000fec00000
[ 0.000000] swsusp: Registered nosave memory region: 00000000fec00000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at c0000000 (gap: bfe00000:20200000)
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] PERCPU: Allocating 42120 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 964130
[ 0.000000] Kernel command line: root=/dev/mapper/jollyserver-root ro quiet splash
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Marking TSC unstable due to TSCs unsynchronized
[ 24.606468] time.c: Detected 2104.480 MHz processor.
[ 24.607429] Console: colour VGA+ 80x25
[ 24.607445] Checking aperture...
[ 24.607448] CPU 0: aperture @ 4000000 size 32 MB
[ 24.607450] Aperture too small (32 MB)
[ 24.616911] No AGP bridge found
[ 24.616913] Your BIOS doesn't leave a aperture memory hole
[ 24.616914] Please enable the IOMMU option in the BIOS setup
[ 24.616916] This costs you 64 MB of RAM
[ 24.642957] Mapping aperture over 65536 KB of RAM @ 4000000
[ 24.675322] Memory: 3782792k/4980736k available (2296k kernel code, 146804k reserved, 1238k data, 308k init)
[ 24.675369] SLUB: Genslabs=23, HWalign=64, Order=0-1, MinObjects=4, CPUs=4, Nodes=1
[ 24.818695] Calibrating delay using timer specific routine.. 4211.51 BogoMIPS (lpj=21057585)
[ 24.818722] Security Framework v1.0.0 initialized
[ 24.818728] SELinux: Disabled at boot.
[ 24.819000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 24.821154] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 24.822204] Mount-cache hash table entries: 256
[ 24.822317] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 24.822320] CPU: L2 Cache: 512K (64 bytes/line)
[ 24.822322] CPU 0/0 -> Node 0
[ 24.822324] CPU: Physical Processor ID: 0
[ 24.822325] CPU: Processor Core ID: 0
[ 24.822341] SMP alternatives: switching to UP code
[ 24.822546] Early unpacking initramfs... done
[ 25.131647] ACPI: Core revision 20070126
[ 25.131710] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 25.246615] Using local APIC timer interrupts.
[ 25.294081] result 12526660
[ 25.294082] Detected 12.526 MHz APIC timer.
[ 25.298176] SMP alternatives: switching to SMP code
[ 25.298257] Booting processor 1/2 APIC 0x1
[ 25.308462] Initializing CPU#1
[ 25.458062] Calibrating delay using timer specific routine.. 4209.06 BogoMIPS (lpj=21045314)
[ 25.458068] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 25.458070] CPU: L2 Cache: 512K (64 bytes/line)
[ 25.458072] CPU 1/1 -> Node 0
[ 25.458074] CPU: Physical Processor ID: 0
[ 25.458075] CPU: Processor Core ID: 1
[ 25.458168] AMD Athlon(tm) X2 Dual Core Processor BE-2350 stepping 02
[ 25.467940] Brought up 2 CPUs
[ 25.849137] migration_cost=619
[ 25.849220] NET: Registered protocol family 16
[ 25.849302] ACPI: bus type pci registered
[ 25.849308] PCI: Using configuration type 1
[ 25.850440] ACPI: EC: Look up EC in DSDT
[ 25.855453] ACPI: Interpreter enabled
[ 25.855458] ACPI: (supports S0 S1 S4 S5)
[ 25.855481] ACPI: Using IOAPIC for interrupt routing
[ 25.860383] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 25.860390] PCI: Probing PCI hardware (bus 00)
[ 25.861854] PCI: Transparent bridge - 0000:00:14.4
[ 25.861892] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 25.862166] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 25.862281] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCEA._PRT]
[ 25.862361] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 25.878873] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 25.878974] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 25.879072] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 25.879169] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 25.879267] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 25.879365] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 25.879463] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 25.879561] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
[ 25.879644] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 25.879655] pnp: PnP ACPI init
[ 25.879664] ACPI: bus type pnp registered
[ 25.882029] pnp: PnP ACPI: found 11 devices
[ 25.882031] ACPI: ACPI bus type pnp unregistered
[ 25.882079] PCI: Using ACPI for IRQ routing
[ 25.882082] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 25.882191] NET: Registered protocol family 8
[ 25.882193] NET: Registered protocol family 20
[ 25.882203] NetLabel: Initializing
[ 25.882204] NetLabel: domain hash size = 128
[ 25.882206] NetLabel: protocols = UNLABELED CIPSOv4
[ 25.882218] NetLabel: unlabeled traffic allowed by default
[ 25.882273] PCI-DMA: Disabling AGP.
[ 25.882518] PCI-DMA: aperture base @ 4000000 size 65536 KB
[ 25.882523] PCI-DMA: using GART IOMMU.
[ 25.882530] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 25.882715] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 25.882720] hpet0: 4 32-bit timers, 14318180 Hz
[ 25.883833] pnp: 00:02: ioport range 0x4100-0x411f has been reserved
[ 25.883835] pnp: 00:02: ioport range 0x228-0x22f has been reserved
[ 25.883838] pnp: 00:02: ioport range 0x238-0x23f has been reserved
[ 25.883841] pnp: 00:02: ioport range 0x40b-0x40b has been reserved
[ 25.883843] pnp: 00:02: ioport range 0x4d6-0x4d6 has been reserved
[ 25.883846] pnp: 00:02: ioport range 0xc00-0xc01 has been reserved
[ 25.883848] pnp: 00:02: ioport range 0xc14-0xc14 has been reserved
[ 25.883851] pnp: 00:02: ioport range 0xc50-0xc52 has been reserved
[ 25.883862] pnp: 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
[ 25.883867] pnp: 00:0a: iomem range 0xd1a00-0xd3fff has been reserved
[ 25.883870] pnp: 00:0a: iomem range 0xf0000-0xf7fff could not be reserved
[ 25.883873] pnp: 00:0a: iomem range 0xf8000-0xfbfff could not be reserved
[ 25.883876] pnp: 00:0a: iomem range 0xfc000-0xfffff could not be reserved
[ 25.884132] PCI: Bridge: 0000:00:01.0
[ 25.884135] IO window: e000-efff
[ 25.884139] MEM window: fde00000-fdffffff
[ 25.884142] PREFETCH window: d0000000-dfffffff
[ 25.884146] PCI: Bridge: 0000:00:0a.0
[ 25.884148] IO window: d000-dfff
[ 25.884151] MEM window: fdd00000-fddfffff
[ 25.884154] PREFETCH window: fdb00000-fdbfffff
[ 25.884158] PCI: Bridge: 0000:00:14.4
[ 25.884161] IO window: c000-cfff
[ 25.884167] MEM window: f8000000-fcffffff
[ 25.884171] PREFETCH window: fdc00000-fdcfffff
[ 25.884197] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 25.884201] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 25.884218] NET: Registered protocol family 2
[ 25.887557] Time: hpet clocksource has been installed.
[ 25.997465] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 25.998776] TCP established hash table entries: 524288 (order: 11, 12582912 bytes)
[ 26.005009] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 26.005554] TCP: Hash tables configured (established 524288 bind 65536)
[ 26.005558] TCP reno registered
[ 26.037358] checking if image is initramfs... it is
[ 26.643553] Freeing initrd memory: 7822k freed
[ 26.648112] audit: initializing netlink socket (disabled)
[ 26.648126] audit(1206481418.000:1): initialized
[ 26.650111] VFS: Disk quotas dquot_6.5.1
[ 26.650159] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 26.650235] io scheduler noop registered
[ 26.650237] io scheduler anticipatory registered
[ 26.650239] io scheduler deadline registered (default)
[ 26.650324] io scheduler cfq registered
[ 26.846547] Boot video device is 0000:01:05.0
[ 26.846697] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 26.846720] assign_interrupt_mode Found MSI capability
[ 26.846723] Allocate Port Service[0000:00:0a.0:pcie00]
[ 26.870126] Real Time Clock Driver v1.12ac
[ 26.870290] hpet_resources: 0xfed00000 is busy
[ 26.870313] Linux agpgart interface v0.102 (c) Dave Jones
[ 26.870315] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 26.870444] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 26.871047] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 26.871691] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 26.871807] input: Macintosh mouse button emulation as /class/input/input0
[ 26.871913] PNP: No PS/2 controller found. Probing ports directly.
[ 26.872229] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 26.872234] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 26.872374] mice: PS/2 mouse device common for all mice
[ 26.872490] TCP cubic registered
[ 26.872549] NET: Registered protocol family 1
[ 26.872738] /build/buildd/linux-source-2.6.22-2.6.22/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 26.872748] Freeing unused kernel memory: 308k freed
[ 28.051326] AppArmor: AppArmor initialized<5>audit(1206481419.400:2): type=1505 info="AppArmor initialized" pid=1232
[ 28.057734] fuse init (API version 7.8)
[ 28.061663] Failure registering capabilities with primary security module.
[ 28.122517] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 28.122528] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 28.133391] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: <email address hidden>
[ 28.985335] SCSI subsystem initialized
[ 29.001236] libata version 2.21 loaded.
[ 29.002663] ahci 0000:00:11.0: version 2.2
[ 29.002691] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 29.002857] ahci 0000:00:11.0: controller can't do 64bit DMA, forcing 32bit
[ 29.024104] usbcore: registered new interface driver usbfs
[ 29.024129] usbcore: registered new interface driver hub
[ 29.024152] usbcore: registered new device driver usb
[ 29.025009] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 30.012667] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[ 30.012672] ahci 0000:00:11.0: flags: ncq ilck pm led clo pmp pio slum part
[ 30.014288] scsi0 : ahci
[ 30.015082] scsi1 : ahci
[ 30.015917] scsi2 : ahci
[ 30.016621] scsi3 : ahci
[ 30.017301] scsi4 : ahci
[ 30.017975] scsi5 : ahci
[ 30.018063] ata1: SATA max UDMA/133 cmd 0xffffc2000142a100 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
[ 30.018069] ata2: SATA max UDMA/133 cmd 0xffffc2000142a180 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
[ 30.018073] ata3: SATA max UDMA/133 cmd 0xffffc2000142a200 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
[ 30.018078] ata4: SATA max UDMA/133 cmd 0xffffc2000142a280 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
[ 30.018083] ata5: SATA max UDMA/133 cmd 0xffffc2000142a300 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
[ 30.018088] ata6: SATA max UDMA/133 cmd 0xffffc2000142a380 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 22
[ 30.551833] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 30.572510] ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7
[ 30.572514] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 30.574488] ata1.00: configured for UDMA/133
[ 30.911398] ata2: SATA link down (SStatus 0 SControl 300)
[ 31.241003] ata3: SATA link down (SStatus 0 SControl 300)
[ 31.570607] ata4: SATA link down (SStatus 0 SControl 300)
[ 32.099975] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 32.272610] ata5.00: ATAPI: SONY DVD RW DRU-190S, 1.62, max UDMA/100
[ 32.452391] ata5.00: configured for UDMA/100
[ 32.789145] ata6: SATA link down (SStatus 0 SControl 300)
[ 32.789377] scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5
[ 32.791343] scsi 4:0:0:0: CD-ROM SONY DVD RW DRU-190S 1.62 PQ: 0 ANSI: 5
[ 32.792754] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 32.792916] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 32.793062] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 1
[ 32.793084] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfe02e000
[ 32.808636] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 32.808647] sd 0:0:0:0: [sda] Write Protect is off
[ 32.808650] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 32.808661] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.808703] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 32.808710] sd 0:0:0:0: [sda] Write Protect is off
[ 32.808712] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 32.808723] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 32.808726] sda:sr0: scsi3-mmc drive: 94x/94x writer dvd-ram cd/rw xa/form2 cdda tray
[ 32.809849] Uniform CD-ROM driver Revision: 3.20
[ 32.809896] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 32.813294] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 32.813318] sr 4:0:0:0: Attached scsi generic sg1 type 5
[ 32.863317] usb usb1: configuration #1 chosen from 1 choice
[ 32.863343] hub 1-0:1.0: USB hub found
[ 32.863354] hub 1-0:1.0: 3 ports detected
[ 32.870192] sda1 sda2 < sda5 >
[ 32.879670] sd 0:0:0:0: [sda] Attached SCSI disk
[ 32.979182] ACPI: PCI Interrupt 0000:00:12.1[A] -> GSI 16 (level, low) -> IRQ 16
[ 32.979347] ohci_hcd 0000:00:12.1: OHCI Host Controller
[ 32.979399] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 2
[ 32.979418] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfe02d000
[ 33.053094] usb usb2: configuration #1 chosen from 1 choice
[ 33.053122] hub 2-0:1.0: USB hub found
[ 33.053132] hub 2-0:1.0: 3 ports detected
[ 33.147633] Attempting manual resume
[ 33.147636] swsusp: Resume From Partition 254:1
[ 33.147638] PM: Checking swsusp image.
[ 33.147809] PM: Resume from disk failed.
[ 33.168943] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 33.169107] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 33.169157] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 3
[ 33.169182] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfe02b000
[ 33.195392] kjournald starting. Commit interval 5 seconds
[ 33.195540] EXT3-fs: mounted filesystem with ordered data mode.
[ 33.242858] usb usb3: configuration #1 chosen from 1 choice
[ 33.242886] hub 3-0:1.0: USB hub found
[ 33.242896] hub 3-0:1.0: 3 ports detected
[ 33.358598] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 33.358710] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 33.358887] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 33.358941] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 4
[ 33.358959] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfe02a000
[ 33.432613] usb usb4: configuration #1 chosen from 1 choice
[ 33.432639] hub 4-0:1.0: USB hub found
[ 33.432649] hub 4-0:1.0: 3 ports detected
[ 33.548498] ACPI: PCI Interrupt 0000:00:14.5[C] -> GSI 18 (level, low) -> IRQ 18
[ 33.548655] ohci_hcd 0000:00:14.5: OHCI Host Controller
[ 33.548710] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 5
[ 33.548727] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfe028000
[ 33.589449] usb 1-1: configuration #1 chosen from 1 choice
[ 33.593392] hub 1-1:1.0: USB hub found
[ 33.595369] hub 1-1:1.0: 2 ports detected
[ 33.622407] usb usb5: configuration #1 chosen from 1 choice
[ 33.622431] hub 5-0:1.0: USB hub found
[ 33.622442] hub 5-0:1.0: 2 ports detected
[ 33.738178] ACPI: PCI Interrupt 0000:03:0e.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 33.738631] ACPI: PCI Interrupt 0000:00:12.2[B] -> GSI 17 (level, low) -> IRQ 17
[ 33.738796] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 33.738852] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 6
[ 33.738890] ehci_hcd 0000:00:12.2: debug port 1
[ 33.738909] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfe02c000
[ 33.738919] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 33.739044] usb usb6: configuration #1 chosen from 1 choice
[ 33.739070] hub 6-0:1.0: USB hub found
[ 33.739076] hub 6-0:1.0: 6 ports detected
[ 33.788355] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[fcfff000-fcfff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 33.858146] ACPI: PCI Interrupt 0000:00:13.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 33.858309] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 33.858360] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 7
[ 33.858401] ehci_hcd 0000:00:13.2: debug port 1
[ 33.858420] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe029000
[ 33.858430] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 33.858531] usb usb7: configuration #1 chosen from 1 choice
[ 33.858556] hub 7-0:1.0: USB hub found
[ 33.858562] hub 7-0:1.0: 6 ports detected
[ 33.978131] r8169 Gigabit Ethernet driver 2.2LK loaded
[ 33.978155] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 33.978174] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 33.978356] eth0: RTL8168b/8111b at 0xffffc20001440000, 00:1d:7d:d4:16:f3, XID 3c2000c0 IRQ 18
[ 34.048845] hub 1-1:1.0: hub_port_status failed (err = -62)
[ 34.050841] hub 1-1:1.0: hub_port_status failed (err = -62)
[ 34.050855] usb 1-1: USB disconnect, address 2
[ 34.816853] usb 7-1: new high speed USB device using ehci_hcd and address 2
[ 34.998801] usb 7-1: configuration #1 chosen from 1 choice
[ 35.126422] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00f3da0300001d7d]
[ 35.336230] usb 1-1: new full speed USB device using ohci_hcd and address 3
[ 35.566177] usb 1-1: configuration #1 chosen from 1 choice
[ 35.570104] hub 1-1:1.0: USB hub found
[ 35.572078] hub 1-1:1.0: 2 ports detected
[ 35.995590] usb 1-1.1: new full speed USB device using ohci_hcd and address 4
[ 36.145500] usb 1-1.1: configuration #1 chosen from 1 choice
[ 36.455057] usb 1-1.2: new low speed USB device using ohci_hcd and address 5
[ 36.606975] usb 1-1.2: configuration #1 chosen from 1 choice
[ 37.500007] r8169: eth0: link up
[ 39.590825] Linux video capture interface: v2.00
[ 39.629400] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 39.645251] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 39.721359] NET: Registered protocol family 17
[ 39.753347] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 39.753353] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 39.783497] input: PC Speaker as /class/input/input1
[ 39.802664] cx2388x v4l2 driver version 0.0.6 loaded
[ 39.802723] ACPI: PCI Interrupt 0000:03:07.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 39.802755] cx88[0]: Your board isn't known (yet) to the driver. You can
[ 39.802757] cx88[0]: try to pick one of the existing card configs via
[ 39.802758] cx88[0]: card=<n> insmod option. Updating to the latest
[ 39.802760] cx88[0]: version might help as well.
[ 39.802762] cx88[0]: Here is a list of valid choices for the card=<n> insmod option:
[ 39.802764] cx88[0]: card=0 -> UNKNOWN/GENERIC
[ 39.802766] cx88[0]: card=1 -> Hauppauge WinTV 34xxx models
[ 39.802768] cx88[0]: card=2 -> GDI Black Gold
[ 39.802770] cx88[0]: card=3 -> PixelView
[ 39.802771] cx88[0]: card=4 -> ATI TV Wonder Pro
[ 39.802773] cx88[0]: card=5 -> Leadtek Winfast 2000XP Expert
[ 39.802775] cx88[0]: card=6 -> AverTV Studio 303 (M126)
[ 39.802777] cx88[0]: card=7 -> MSI TV-@nywhere Master
[ 39.802779] cx88[0]: card=8 -> Leadtek Winfast DV2000
[ 39.802781] cx88[0]: card=9 -> Leadtek PVR 2000
[ 39.802782] cx88[0]: card=10 -> IODATA GV-VCP3/PCI
[ 39.802784] cx88[0]: card=11 -> Prolink PlayTV PVR
[ 39.802786] cx88[0]: card=12 -> ASUS PVR-416
[ 39.802788] cx88[0]: card=13 -> MSI TV-@nywhere
[ 39.802790] cx88[0]: card=14 -> KWorld/VStream XPert DVB-T
[ 39.802792] cx88[0]: card=15 -> DViCO FusionHDTV DVB-T1
[ 39.802794] cx88[0]: card=16 -> KWorld LTV883RF
[ 39.802795] cx88[0]: card=17 -> DViCO FusionHDTV 3 Gold-Q
[ 39.802797] cx88[0]: card=18 -> Hauppauge Nova-T DVB-T
[ 39.802799] cx88[0]: card=19 -> Conexant DVB-T reference design
[ 39.802801] cx88[0]: card=20 -> Provideo PV259
[ 39.802803] cx88[0]: card=21 -> DViCO FusionHDTV DVB-T Plus
[ 39.802805] cx88[0]: card=22 -> pcHDTV HD3000 HDTV
[ 39.802807] cx88[0]: card=23 -> digitalnow DNTV Live! DVB-T
[ 39.802809] cx88[0]: card=24 -> Hauppauge WinTV 28xxx (Roslyn) models
[ 39.802811] cx88[0]: card=25 -> Digital-Logic MICROSPACE Entertainment Center (MEC)
[ 39.802813] cx88[0]: card=26 -> IODATA GV/BCTV7E
[ 39.802815] cx88[0]: card=27 -> PixelView PlayTV Ultra Pro (Stereo)
[ 39.802817] cx88[0]: card=28 -> DViCO FusionHDTV 3 Gold-T
[ 39.802819] cx88[0]: card=29 -> ADS Tech Instant TV DVB-T PCI
[ 39.802821] cx88[0]: card=30 -> TerraTec Cinergy 1400 DVB-T
[ 39.802823] cx88[0]: card=31 -> DViCO FusionHDTV 5 Gold
[ 39.802825] cx88[0]: card=32 -> AverMedia UltraTV Media Center PCI 550
[ 39.802827] cx88[0]: card=33 -> Kworld V-Stream Xpert DVD
[ 39.802829] cx88[0]: card=34 -> ATI HDTV Wonder
[ 39.802831] cx88[0]: card=35 -> WinFast DTV1000-T
[ 39.802832] cx88[0]: card=36 -> AVerTV 303 (M126)
[ 39.802834] cx88[0]: card=37 -> Hauppauge Nova-S-Plus DVB-S
[ 39.802836] cx88[0]: card=38 -> Hauppauge Nova-SE2 DVB-S
[ 39.802838] cx88[0]: card=39 -> KWorld DVB-S 100
[ 39.802840] cx88[0]: card=40 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid
[ 39.802842] cx88[0]: card=41 -> Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profile)
[ 39.802844] cx88[0]: card=42 -> digitalnow DNTV Live! DVB-T Pro
[ 39.802846] cx88[0]: card=43 -> KWorld/VStream XPert DVB-T with cx22702
[ 39.802848] cx88[0]: card=44 -> DViCO FusionHDTV DVB-T Dual Digital
[ 39.802850] cx88[0]: card=45 -> KWorld HardwareMpegTV XPert
[ 39.802852] cx88[0]: card=46 -> DViCO FusionHDTV DVB-T Hybrid
[ 39.802854] cx88[0]: card=47 -> pcHDTV HD5500 HDTV
[ 39.802856] cx88[0]: card=48 -> Kworld MCE 200 Deluxe
[ 39.802858] cx88[0]: card=49 -> PixelView PlayTV P7000
[ 39.802860] cx88[0]: card=50 -> NPG Tech Real TV FM Top 10
[ 39.802862] cx88[0]: card=51 -> WinFast DTV2000 H
[ 39.802864] cx88[0]: card=52 -> Geniatech DVB-S
[ 39.802865] cx88[0]: card=53 -> Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
[ 39.802868] cx88[0]: card=54 -> Norwood Micro TV Tuner
[ 39.802870] cx88[0]: card=55 -> Shenzhen Tungsten Ages Tech TE-DTV-250 / Swann OEM
[ 39.802872] cx88[0]: card=56 -> Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder
[ 39.802875] CORE cx88[0]: subsystem: 0070:6902, board: UNKNOWN/GENERIC [card=0,autodetected]
[ 39.802878] TV tuner -1 at 0x1fe, Radio tuner -1 at 0x1fe
[ 39.813128] shpchp: HPC vendor_id 1022 device_id 9602 ss_vid 0 ss_did 0
[ 39.813133] shpchp: shpc_init: cannot reserve MMIO region
[ 39.863529] usbcore: registered new interface driver hiddev
[ 39.866283] input: BTC Multimedia USB Keyboard as /class/input/input2
[ 39.866308] input: USB HID v1.10 Keyboard [BTC Multimedia USB Keyboard] on usb-0000:00:12.0-1.1
[ 39.871392] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input3
[ 39.871428] input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:12.0-1.2
[ 39.871442] usbcore: registered new interface driver usbhid
[ 39.871445] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 39.911858] cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
[ 39.940307] usbcore: registered new interface driver libusual
[ 39.946176] Initializing USB Mass Storage driver...
[ 39.946448] scsi6 : SCSI emulation for USB Mass Storage devices
[ 39.946532] usbcore: registered new interface driver usb-storage
[ 39.946535] USB Mass Storage support registered.
[ 39.946539] usb-storage: device found at 2
[ 39.946540] usb-storage: waiting for device to settle before scanning
[ 39.979544] cx88[0]/0: found at 0000:03:07.0, rev: 5, irq: 21, latency: 32, mmio: 0xf9000000
[ 40.030805] cx88[0]/0: registered device video0 [v4l2]
[ 40.030825] cx88[0]/0: registered device vbi0
[ 40.030832] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 40.031344] cx88[0]/2: cx2388x 8802 Driver Manager
[ 40.032030] SB600_PATA: IDE controller at PCI slot 0000:00:14.1
[ 40.032046] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
[ 40.032057] SB600_PATA: chipset revision 0
[ 40.032060] SB600_PATA: not 100% native mode: will probe irqs later
[ 40.032067] ide0: BM-DMA at 0xfa00-0xfa07, BIOS settings: hda:pio, hdb:pio
[ 40.032079] Probing IDE interface ide0...
[ 40.112171] cx2388x alsa driver version 0.0.6 loaded
[ 40.649791] ACPI: PCI Interrupt 0000:03:07.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 40.649822] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
[ 40.652449] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
[ 41.179223] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
[ 42.268480] loop: module loaded
[ 42.330401] lp: driver loaded but no devices found
[ 42.404229] Adding 10584056k swap on /dev/mapper/jollyserver-swap_1. Priority:-1 extents:1 across:10584056k
[ 42.862262] EXT3 FS on dm-0, internal journal
[ 43.164547] kjournald starting. Commit interval 5 seconds
[ 43.164849] EXT3 FS on sda1, internal journal
[ 43.164855] EXT3-fs: mounted filesystem with ordered data mode.
[ 43.936924] NET: Registered protocol family 10
[ 43.937018] lo: Disabled Privacy Extensions
[ 44.323755] No dock devices found.
[ 44.332966] input: Power Button (FF) as /class/input/input4
[ 44.332983] ACPI: Power Button (FF) [PWRF]
[ 44.333018] input: Power Button (CM) as /class/input/input5
[ 44.333030] ACPI: Power Button (CM) [PWRB]
[ 44.805528] powernow-k8: Found 2 AMD Athlon(tm) X2 Dual Core Processor BE-2350 processors (version 2.00.00)
[ 44.805422] powernow-k8: 0 : fid 0xd (2100 MHz), vid 0xe
[ 44.805426] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xf
[ 44.805429] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0x11
[ 44.805431] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x16
[ 44.944901] usb-storage: device scan complete
[ 44.945518] scsi 6:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
[ 44.948809] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 44.948856] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 46.096820] ppdev: user-space parallel port driver
[ 46.278069] audit(1206481438.163:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5177 profile="/usr/sbin/cupsd"
[ 49.567584] Failure registering capabilities with primary security module.
[ 50.749305] Bluetooth: Core ver 2.11
[ 50.749359] NET: Registered protocol family 31
[ 50.749361] Bluetooth: HCI device and connection manager initialized
[ 50.749364] Bluetooth: HCI socket layer initialized
[ 50.774450] Bluetooth: L2CAP ver 2.8
[ 50.774454] Bluetooth: L2CAP socket layer initialized
[ 50.849379] Bluetooth: RFCOMM socket layer initialized
[ 50.849394] Bluetooth: RFCOMM TTY layer initialized
[ 50.849398] Bluetooth: RFCOMM ver 1.8
[ 51.962997] eth0: no IPv6 routers present
[ 55.826087] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 67.525755] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 67.565368] ISO 9660 Extensions: RRIP_1991A
[ 1020.860531] cx25840: Unknown parameter `card'

[lspci]

00:00.0 Host bridge: Advanced Micro Devices [AMD] Unknown device 9600
00:01.0 PCI bridge: Advanced Micro Devices [AMD] Unknown device 9602
00:0a.0 PCI bridge: Advanced Micro Devices [AMD] Unknown device 9609
00:11.0 SATA controller: ATI Technologies Inc SB700 SATA Controller [AHCI mode]
00:12.0 USB Controller: ATI Technologies Inc SB700 USB OHCI0 Controller
00:12.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller
00:12.2 USB Controller: ATI Technologies Inc SB700 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB700 USB OHCI0 Controller
00:13.1 USB Controller: ATI Technologies Inc SB700 USB OHCI1 Controller
00:13.2 USB Controller: ATI Technologies Inc SB700 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 3a)
00:14.1 IDE interface: ATI Technologies Inc SB700 IDE
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia
00:14.3 ISA bridge: ATI Technologies Inc SB700 LPC host controller
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge
00:14.5 USB Controller: ATI Technologies Inc SB700 USB OHCI2 Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
01:05.0 VGA compatible controller: ATI Technologies Inc Unknown device 9610
01:05.1 Audio device: ATI Technologies Inc Unknown device 960f
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
03:07.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
03:07.1 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] (rev 05)
03:07.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
03:07.4 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05)
03:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)