laserjet 1000 not printing pages in ubuntu 8.4 lts endition

I have typed the commands provided by HPLIP in terminal .also I HAVE insatlled application of HPLIP FAX UTILITY

Good Day

can you post the output to the following command.

$ hp-check -t

Thanks

jh

Hi, john. Thanks for help.

I have the same problem. I tested the printer on two different (Kubuntu - Hardy Heron) computer with the same results.

I executed the command. I got a long output. Therefore I decide to post only the link:
http://ramm.gmxhome.de/forum/hplib/hp-check.txt

In the text are some apt-get commands in the chapter "COMPILE AND RUNTIME DEPENDENCIES". Do I have to execute them all?

Regards, Sap

I have run the listed apt-get commands (from bottom of the log-file). But now if I execute the command "hp-testpage" I get this errors:

+++++++ begin of output +++++++
error: Unable to communicate with device (code=12): hp:/par/HP_LaserJet_1100?device=/dev/parport0
error: Unable to print to printer. Please check device and try again.

note: If an error occured, or the test page failed to print, refer to the HPLIP website
note: at: http://hplip.sourceforge.net for troubleshooting and support.
+++++++ end of output +++++++

nobody has an idea? I can submit more information. Please let me know which information are missing. Or is the status of this thread wrong? "Answered" sounds as "already solved". How can I switch the status to "open"?

Hello,

Now I have installed hplip 2.8.7 and now I can print the hp-testpage. But I can not print lager pages.

Below is the Systemlog.
****************** Begin **************
03.08.2008 17:22:12 pc-001 python hp-systray(hpssd)[5547]: error: Unable to connect to dbus session bus. Exiting.

03.08.2008 17:23:53 pc-001 kernel [ 210.923464] ppdev0: registered pardevice

03.08.2008 17:23:56 pc-001 kernel [ 213.944888] sysctl table check failed: /dev/parport/parport0/devices/ppdev0/timeslice Sysctl already exists

03.08.2008 17:23:56 pc-001 kernel [ 213.944910] Pid: 5670, comm: hpijs Tainted: P 2.6.24-19-generic #1

03.08.2008 17:23:56 pc-001 kernel [ 213.944942] [set_fail+0x45/0x60] set_fail+0x45/0x60

03.08.2008 17:23:56 pc-001 kernel [ 213.944960] [sysctl_check_table+0x296/0x5b0] sysctl_check_table+0x296/0x5b0

03.08.2008 17:23:56 pc-001 kernel [ 213.944966] [sysctl_head_finish+0x18/0x30] sysctl_head_finish+0x18/0x30

03.08.2008 17:23:56 pc-001 kernel [ 213.944980] [sysctl_check_table+0x2aa/0x5b0] sysctl_check_table+0x2aa/0x5b0

03.08.2008 17:23:56 pc-001 kernel [ 213.944985] [sysctl_head_finish+0x18/0x30] sysctl_head_finish+0x18/0x30

03.08.2008 17:23:56 pc-001 kernel [ 213.944995] [sysctl_check_table+0x2aa/0x5b0] sysctl_check_table+0x2aa/0x5b0

03.08.2008 17:23:56 pc-001 kernel [ 213.944999] [sysctl_head_finish+0x18/0x30] sysctl_head_finish+0x18/0x30

03.08.2008 17:23:56 pc-001 kernel [ 213.945009] [sysctl_check_table+0x2aa/0x5b0] sysctl_check_table+0x2aa/0x5b0

03.08.2008 17:23:56 pc-001 kernel [ 213.945014] [sysctl_head_finish+0x18/0x30] sysctl_head_finish+0x18/0x30

03.08.2008 17:23:56 pc-001 kernel [ 213.945023] [sysctl_check_table+0x2aa/0x5b0] sysctl_check_table+0x2aa/0x5b0

03.08.2008 17:23:56 pc-001 kernel [ 213.945028] [sysctl_head_finish+0x18/0x30] sysctl_head_finish+0x18/0x30

03.08.2008 17:23:56 pc-001 kernel [ 213.945037] [sysctl_check_table+0x2aa/0x5b0] sysctl_check_table+0x2aa/0x5b0

03.08.2008 17:23:56 pc-001 kernel [ 213.945042] [sysctl_set_parent+0x19/0x30] sysctl_set_parent+0x19/0x30

03.08.2008 17:23:56 pc-001 kernel [ 213.945052] [ipv6:register_sysctl_table+0x50/0x150] register_sysctl_table+0x50/0xa0

03.08.2008 17:23:56 pc-001 kernel [ 213.945059] [<e0a7a90e>] parport_device_proc_register+0xae/0xe0 [parport]

03.08.2008 17:23:56 pc-001 kernel [ 213.945079] [<e0a78e29>] parport_register_device+0x139/0x260 [parport]

03.08.2008 17:23:56 pc-001 kernel [ 213.945094] [<e0c90765>] pp_ioctl+0x445/0x830 [ppdev]

03.08.2008 17:23:56 pc-001 kernel [ 213.945101] [<e0c90240>] pp_irq+0x0/0x50 [ppdev]

03.08.2008 17:23:56 pc-001 kernel [ 213.945112] [do_ioctl+0x78/0x90] do_ioctl+0x78/0x90

03.08.2008 17:23:56 pc-001 kernel [ 213.945122] [vfs_ioctl+0x22e/0x2b0] vfs_ioctl+0x22e/0x2b0

03.08.2008 17:23:56 pc-001 kernel [ 213.945127] [do_sys_open+0xbe/0xe0] do_sys_open+0xbe/0xe0

03.08.2008 17:23:56 pc-001 kernel [ 213.945135] [sys_ioctl+0x56/0x70] sys_ioctl+0x56/0x70

03.08.2008 17:23:56 pc-001 kernel [ 213.945142] [sysenter_past_esp+0x6b/0xa9] sysenter_past_esp+0x6b/0xa9

03.08.2008 17:23:56 pc-001 kernel [ 213.945158] =======================

03.08.2008 17:23:56 pc-001 kernel [ 213.945162] ppdev0: registered pardevice

03.08.2008 17:24:43 pc-001 kernel [ 261.511401] ppdev0: unregistered pardevice

03.08.2008 17:24:57 pc-001 kernel [ 274.896340] ppdev0: unregistered pardevice

****************** End **************

The syslog above is plotted while a smaller page was print. Here is the syslog of a bigger page. After 3/4 of the page the printing stops.

****************** Begin **************
03.08.2008 17:35:16 pc-001 parport0 io/hpmud/mlc.c 463: unable to write MlcForwardData header: Resource temporarily unavailable

03.08.2008 17:35:16 pc-001 parport0 io/hpmud/mlc.c 470: unable to write MlcForwardData: Resource temporarily unavailable

03.08.2008 17:35:16 pc-001 parport0 io/hpmud/pp.c 313: ecp_write_data transfer stalled

03.08.2008 17:35:16 pc-001 parport0 io/hpmud/pp.c 316: ecp_write_data host transfer recovery cnt=1

03.08.2008 17:35:16 pc-001 parport0 io/hpmud/pp.c 316: ecp_write_data host transfer recovery cnt=2

03.08.2008 17:35:16 pc-001 parport0 io/hpmud/pp.c 316: ecp_write_data host transfer recovery cnt=3

03.08.2008 17:35:16 pc-001 parport0 io/hpmud/pp.c 316: ecp_write_data host transfer recovery cnt=4

03.08.2008 17:36:34 pc-001 parport0 io/hpmud/mlc.c 179: unable to read MlcReverseCmd header: Resource temporarily unavailable

03.08.2008 17:36:34 pc-001 parport0 io/hpmud/musb.c 1583: invalid MlcCredit from peripheral, trying miser

03.08.2008 17:37:09 pc-001 parport0 io/hpmud/mlc.c 238: unable to read MlcReverseReply header: Resource temporarily unavailable bytesRead=0

03.08.2008 17:37:09 pc-001 parport0 io/hpmud/mlc.c 760: invalid MlcCreditRequestReply: cmd=4, result=2

03.08.2008 17:37:09 pc-001 parport0 io/hpmud/musb.c 1567: invalid MlcCreditRequest from peripheral

03.08.2008 17:37:43 pc-001 parport0 io/hpmud/mlc.c 238: unable to read MlcReverseReply header: Resource temporarily unavailable bytesRead=0

03.08.2008 17:37:43 pc-001 parport0 io/hpmud/mlc.c 760: invalid MlcCreditRequestReply: cmd=4, result=2

03.08.2008 17:37:43 pc-001 parport0 io/hpmud/musb.c 1567: invalid MlcCreditRequest from peripheral

03.08.2008 17:38:17 pc-001 parport0 io/hpmud/mlc.c 238: unable to read MlcReverseReply header: Resource temporarily unavailable bytesRead=0

03.08.2008 17:38:17 pc-001 parport0 io/hpmud/mlc.c 760: invalid MlcCreditRequestReply: cmd=4, result=2

03.08.2008 17:38:17 pc-001 parport0 io/hpmud/musb.c 1567: invalid MlcCreditRequest from peripheral
****************** End **************

I'm having the same problem on ubuntu 8.04 and 8.10 with an HP PSC 1210.

does the gutenprint driver work (instead of hplip)?